Difference between revisions of "Securing the T1® to the Microphone Stand Bracket"
m |
m (ST moved page Securing the T1® to the Microphone Stand Bracket to Securing the T1® to the Microphone Stand Bracket) |
||
(2 intermediate revisions by the same user not shown) | |||
Line 33: | Line 33: | ||
— [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9600024746?r=4800036746#4800036746 source] | — [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9600024746?r=4800036746#4800036746 source] | ||
+ | {{T1® Microphone Stand Bracket Tips}} | ||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | |||
+ | <!-- | ||
<html><img src="http://bose.infopop.cc/eve/forums/a/ga/ul/6190039046/inlineimg/Y/T1-1.jpg" width="640" alt="source: http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/1640046046?r=5190039046#5190039046"></html> | <html><img src="http://bose.infopop.cc/eve/forums/a/ga/ul/6190039046/inlineimg/Y/T1-1.jpg" width="640" alt="source: http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/1640046046?r=5190039046#5190039046"></html> | ||
— [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/1640046046?r=5190039046#5190039046 source] | — [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/1640046046?r=5190039046#5190039046 source] | ||
− | + | --> | |
Comments? Please join the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9540096066 discussion on the Bose L1® Forum] | Comments? Please join the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/9540096066 discussion on the Bose L1® Forum] |
Latest revision as of 05:11, 26 March 2017
- The bracket that sits parallel to the floor has a bevel on the top. The bevel should run down, facing you. If the bevel runs down away from you, the bracket is upside down and the T1 ToneMatch® Audio Engine will not sit properly on top of it.
- correct - bevel running down, facing you
- incorrect (upside down)- bevel on opposite side, away from you
This is how I secure the T1® to the T1® Microphone Stand Bracket[1]
- There is a velcro strap on the black ToneMatch cable.
- I use the velcro to secure the ToneMatch cable to the microphone stand just above the Microphone Stand Adapter (the thing that clamps around the mic stand).
- Then I insert the ToneMatch cable into the T1®. It locks into place.
- At this point, most people would put the T1® on the bracket and attach the other cables.
- I insert all the other cables into the T1® before I put it on the bracket. I do it this way because I have all my cables strapped to the microphone stand (I don't take them off between gigs). So there's no hanging stress from those either.
- Finally, I set the T1® on top of the bracket.
In the picture above, I am using all the inputs and the cables are heavy. But since I have all the cables secured by a velcro strap, there's no chance that the T1® will come off the microphone stand bracket.
The white cable is a network cable (Cat-5) instead of the ToneMatch® cable
— source
Here's how I have one of my microphone stands setup. The T1® Microphone Stand Bracket is attached and I never remove it.
All the cables are also strapped to the microphone stand. I leave the cables attached all the time. This saves a great deal of time during setup and teardown.
I used a white background so that you could see the wires. Normally they don't stand out like this visually. Notice that even if the T1® were to get knocked off the bracket the cables are acting as safety tethers.
- View from the Back
- Ready to Pack Up
You can see that the cables are strapped to the microphone stand.
- Packed, ready to zip up
The black bag is one of the original Cylindrical Radiator® bags that came with my L1®. Years ago I got some heavy duty bags for the Cylindrical Radiator® and it turns out that the stock bags work great for holding microphone and light stands.
- Remember to pack the Bracket (arm) in the T1® Lid.
Comments? Please join the discussion on the Bose L1® Forum
- ↑ Original discussion about using the T1® Microphone stand adapter