Difference between revisions of "T1 ToneMatch® Audio Engine / Connections to Model II"
m (link to standard T1 ToneMatch® Audio Engine Power Supply page) |
m (ST moved page T1 ToneMatch® Audio Engine / Connections to Model II to T1 ToneMatch® Audio Engine / Connections to Model II) |
||
(16 intermediate revisions by the same user not shown) | |||
Line 1: | Line 1: | ||
− | The {{Model II}} can accept two inputs. [[Image: | + | __NOEDITSECTION__ |
+ | The {{Model II}} can accept two inputs. [[Image:ModelIIInputsForTwoLT1.png|200px|right|Model II inputs]] | ||
− | + | This makes it easy for two performers to connect their own T1®s to a {{Model II nl}} Power Stand. | |
− | + | ==== {{ToneMatch}} Input ==== | |
− | + | The {{ToneMatch}} connection is specifically designed for a {{T1}}. The [[ToneMatch® Cable|ToneMatch® cable]] is supplied with the {{T1}} and uses a male [[Ethercon]] connector at both ends. | |
− | The Analog connection is a ¼ inch phone jack. You can use this for a | + | ==== Analog Input==== |
+ | <section begin=AnalogInput /> | ||
+ | [[Image:Analog Input 3.png|300px|right|Model II/Model 1S analog input]] | ||
+ | The Analog connection is a ¼ inch phone jack. You can use this for a second T1® using the T1® Analog Master output (¼ inch phone jack). | ||
− | This connection is made with a standard ¼ inch jack instrument cable. This can be Tip-Sleeve or Tip-Ring-Sleeve connectors. | + | This connection is made with a standard ¼ inch jack instrument cable. This can be Tip-Sleeve or Tip-Ring-Sleeve connectors. |
− | Note: A T1® connected to the the Analog input will require the optional [[T1 ToneMatch® Audio Engine power supply]]. | + | Set Power Stand Analog Input Trim to '''3''' to have approximately the same level as you would have if you had connected with the {{ToneMatch}} connection. You may have to adjust this, but '''3''' is a good place to start. |
+ | <section end=AnalogInput /> | ||
+ | Note: A T1® connected to the the Analog input will require the optional [[T1 ToneMatch® Audio Engine power supply]]. | ||
− | + | === Analog Connection from the Second T1® to the Model II Power Stand === | |
+ | [[Image:T1x2IntoModelII.gif]] | ||
− | + | {{#lst:T1 ToneMatch® Audio Engine / 1/4 inch Output Connections to L1® Family Members |Balanced}} | |
---- | ---- | ||
+ | [[Category:Connections]] | ||
+ | |||
+ | [[Category:Model_II]] | ||
+ | |||
+ | [[Category:Stage Layout]] | ||
− | + | [[Category:T1]] |
Latest revision as of 04:42, 26 March 2017
The L1 Model II can accept two inputs.
This makes it easy for two performers to connect their own T1®s to a L1® Model II Power Stand.
Contents
ToneMatch® Input
The ToneMatch® connection is specifically designed for a T1 ToneMatch Audio Engine. The ToneMatch® cable is supplied with the T1 ToneMatch Audio Engine and uses a male Ethercon connector at both ends.
Analog Input
The Analog connection is a ¼ inch phone jack. You can use this for a second T1® using the T1® Analog Master output (¼ inch phone jack).
This connection is made with a standard ¼ inch jack instrument cable. This can be Tip-Sleeve or Tip-Ring-Sleeve connectors.
Set Power Stand Analog Input Trim to 3 to have approximately the same level as you would have if you had connected with the ToneMatch® connection. You may have to adjust this, but 3 is a good place to start.
Note: A T1® connected to the the Analog input will require the optional T1 ToneMatch® Audio Engine power supply.
Analog Connection from the Second T1® to the Model II Power Stand
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.
¼ Inch Tip-Ring-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine but a balanced connection (immediately above) is preferred especially if you will have cable runs in excess of 20 feet (6 meters) or if you hear line noise, hum or hiss.