Search results

Create the page "Powered Mixer" on this wiki! See also the search results found.

• Powered Mixers
  ==Can I use a powered mixer?== ...red mixer to any Bose Portable PA equipment including ToneMatch mixers and powered loudspeakers (L1, F1, S1 Pro)
  4 KB (664 words) - 22:22, 16 November 2019
• Power Sequence
  * Turn on the powered loudspeakers last. * Turn off the powered loudspeakers first.
  2 KB (266 words) - 12:47, 22 November 2019
• Template:S1 Pro+ FAQ
  ...d by Auto EQ, ensure that you always sound your best. And with a 3-channel mixer, reverb, Bluetooth streaming along with integrated wireless receivers, the ...and a 3.5 mm input allow for connecting additional wired sources like a DJ mixer, laptop, CD, or portable audio device. When making announcements, simply pl
  23 KB (3,811 words) - 19:28, 31 July 2024
• Is It Too Expensive?
  ..., I couldn't perceive a lot of value in the old stuff. (Bose 802s, powered mixer, power amps, floor wedge monitors). So I donated it all to a worthy cause. ...System has onboard amplifiers and integrated speakers. So to some, it's a powered speaker.
  16 KB (2,913 words) - 11:43, 9 May 2011
• Kemper Profiler
  ...The number of rigs in memory does only make a difference when the unit was powered off accidentally. If you use the power button or the chicken head to power == Kemper Powered Kab ==
  24 KB (3,721 words) - 12:54, 8 August 2023
• Talk:Crossover
  ...ience with the B1...<br><br>We are playing through a PAS, with a KLH E-8FS powered subwoofer. After using the B1 a few times, I was very unhappy with the "rum
  22 KB (4,268 words) - 17:58, 5 April 2013
• Ground Loop
  ...o the audio signal at the mixer with headphones. If the buzz exists at the mixer then do the following: ...uts or outputs are disconnected which are connected to devices that are AC powered, then it is likely caused by a ground loop.
  8 KB (1,303 words) - 09:31, 7 April 2019
• Should I get an L1 Pro16 or L1 Pro32
  ...an be controlled using the Bose Music App, and you can connect a ToneMatch mixer to the ToneMatch port. ...ong (32 drivers) and powered by 480 watts RMS. The L1 Pro16 has 16 drivers powered by 240 watts RMS.
  15 KB (2,633 words) - 13:17, 27 July 2024
• Template talk:S1 Pro+ FAQ
  ...d by Auto EQ, ensure that you always sound your best. And with a 3-channel mixer, reverb, Bluetooth streaming along with integrated wireless receivers, the ...and a 3.5 mm input allow for connecting additional wired sources like a DJ mixer, laptop, CD, or portable audio device. When making announcements, simply pl
  12 KB (2,055 words) - 19:03, 31 July 2024
• F1 Model 812 Flexible Array Loudspeaker
  ...T1}} or {{ToneMatch Mixer}}) to the maximum you can without clipping. On a mixer this may be shown as unity or 0. ==== Stereo + Mixer ====
  20 KB (3,191 words) - 00:30, 18 July 2024
• Template:T4S/T8S FAQ
  <h2>T4S/T8S ToneMatch Mixer FAQs</h2> What is the T4S/T8S ToneMatch Mixer?
  23 KB (3,780 words) - 01:32, 8 February 2018
• S1 Pro Line Out to a Third Party Device
  If another device (like a third-party mixer or powered loudspeaker) has a 1/4 inch (6 mm) input, and you don't know if it's balanc Many modern powered loudspeakers will accept a balanced line-level device. If you use a Tip-Rin
  3 KB (500 words) - 22:20, 16 November 2019
• Phantom Power
  What is a "phantom powered" microphone? Does that mean that the microphone draws its power from a remo ...veling down. Thus, the microphone is receiving the power remotely from the mixer.
  8 KB (1,252 words) - 19:43, 10 March 2020
• Template:T4S/T8S Mono Output
  On the back of {{ToneMatch Mixer}}s, there is an indication below the Right output (MONO). ===T4S ToneMatch® mixer===
  2 KB (345 words) - 18:46, 12 February 2024
• McIntyre BluesMaker II
  ...the guitarist, who demands tonal variations not found on conventional low powered amplifiers. The Bluesmaker MKII is a masterpiece of complex tone voicings w ...recording amp and direct source. When connected to a recording or PA mixer,<br>
  34 KB (5,610 words) - 15:00, 18 January 2021
• Mixer Left Output Only
  When using a mixer is some of the quality lost using just the left output? Connecting a stereo mixer to a mono {{L1}}. {{Compact}}, {{Model 1S}}, {{Model 1S}}, {{F1}}
  1 KB (198 words) - 11:48, 1 September 2018
• T4S/T8S ToneMatch® Mixer
  {{T4S/T8S ToneMatch Mixer Owners Guide}} ...://global.bose.com/en_us/product_registration.html Register your ToneMatch mixer]
  9 KB (1,484 words) - 23:55, 13 December 2023
• Template:F1 Subwoofer FAQ
  ...align="left">Engineered with an array of eight high-output drivers, a high-powered 12-inch woofer and a lower crossover point, the loudspeaker delivers full-r <div><p align="left">Current popular powered loudspeakers are standard two-way designs consisting of a single horn-loade
  14 KB (2,038 words) - 12:29, 14 May 2016
• Template:F1 Model 812 FAQ
  ...align="left">Engineered with an array of eight high-output drivers, a high-powered 12-inch woofer and a lower crossover point, the loudspeaker delivers full-r <div><p align="left">Current popular powered loudspeakers are standard two-way designs consisting of a single horn-loade
  15 KB (2,087 words) - 11:11, 14 February 2019
• Multi Mono
  * Running multiple powered loudspeakers ({{L1}}, {{F1}}, {{S1}}, [[L1 Pro]] or other) * Every sound source is heard through only one powered loudspeaker
  564 bytes (86 words) - 23:24, 11 June 2021

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)