Difference between revisions of "L1® Model II Power Stand / Bass Line Out"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m (signed introduction)
m (shortened title, setup for includes)
Line 1: Line 1:
 +
<noinclude>
 
__NOEDITSECTION__
 
__NOEDITSECTION__
 
<table><tr>
 
<table><tr>
Line 8: Line 9:
 
</td>
 
</td>
 
</tr></table>  
 
</tr></table>  
 +
</noinclude>
 +
<includeonly>[[Image:ModelIIBassOutputs.png|Model II Bass Outputs]]</includeonly>
  
 
+
==Bass Line Out and B1 behavior ==
 
 
== {{Model II}} Bass Line Out and B1 behavior ==
 
 
Hilmar-at-Bose<ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6121039062/r/2641067362#2641067362  A1 PackLite Questions and More Bass Talk]</ref>.
 
Hilmar-at-Bose<ref>Hilmar-at-Bose [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6121039062/r/2641067362#2641067362  A1 PackLite Questions and More Bass Talk]</ref>.
 
This is based on the design goal that “You should always sound the same; no matter how much Bass stuff is attached” I can try to explain my view of why this is a good design goal (of which you may disagree) but let’s look at the actual behavior first.
 
This is based on the design goal that “You should always sound the same; no matter how much Bass stuff is attached” I can try to explain my view of why this is a good design goal (of which you may disagree) but let’s look at the actual behavior first.

Revision as of 00:18, 5 September 2007


Most of the information here was originally written for the L1 Classic and L1 Model I. I have verified with MikeZ-at-Bose, that this is applicable to the L1 Model II as well. There is a little more detail about the L1 Model II crossover at the end. ST

Model II Bass Outputs


Bass Line Out and B1 behavior

Hilmar-at-Bose[1]. This is based on the design goal that “You should always sound the same; no matter how much Bass stuff is attached” I can try to explain my view of why this is a good design goal (of which you may disagree) but let’s look at the actual behavior first.

Without Bass Line out

  • 1 x B1: 40Hz-180Hz, B1 specific EQ, some nominal gain that we call 0dB
  • 2 x B1: 40Hz-180Hz, B1 specific EQ, -6dB as compared to nominal

With Bass Line Out

What this complex behavior does is the following. No matter if you attach 1, 2, or 4 B1s, you will get pretty much the same balance between all combined B1s and the L1s. It’s a little off for 3, 5, 6, 7 & 8 B1s, but still reasonably close.

It’s true that the user doesn’t have to re-EQ our systems if you add more B1s or even a PackLite with another pair of B1s. But that’s unique to our system, because we were actively measuring the number of B1s attached. So re-EQ is required, but the system is doing it by itself without any user involvement required. [2]


With More Than 4 B1s

A little more insight. [3] We actually can't measure the exact number of Packlites, so there is a slight error if you use anything but 1,2, or 4 B1s. For 6 B1s you will be 3.5 dB bass heavy, for 8 B1s it'll be 6 dB. However, these are rare cases, and if you go through the trouble to hook up 8 B1s, I guess you are actually looking for something more bass heavy.

Don't ask how I know.

L1 Model II Crossover L1 Cylindrical Radiator® loudspeaker

There is no change in crossover frequency for the Cylindrical Radiators® depending on the presence/absence of B1s attached to the Bass Module output. This is due to the design change (Cylindrical Radiator® is not ported whereas Classic and Model I are.) The L1 Model II is designed to always be used with at least one B1, whereas the L1 Model I / L1 Classic was designed to used with or without a B1.


Bass Module Output (powered output)

For the sake of those attaching third party passive speakers (an unsupported application).

Output if no B1s detected

  • 40-180 Hz Bandpass (that is: NO B1 EQ)

If one or B1s detected (or resistors used across NL4 2+ / 2- pins to emulate detection)[4]



  • 40-180 Hz with different EQ curves