Difference between revisions of "Pad"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m
m (More Formal Definitions)
Line 31: Line 31:
 
"attenuator or attenuator pad Electronics. A passive network that reduces the voltage (or power; see usage note under gain) level of a signal with negligible distortion, but with insertion loss. Often a purely resistive network, although any combination of inductors, resistors and capacitors are possible, a pad may also provide impedance matching."
 
"attenuator or attenuator pad Electronics. A passive network that reduces the voltage (or power; see usage note under gain) level of a signal with negligible distortion, but with insertion loss. Often a purely resistive network, although any combination of inductors, resistors and capacitors are possible, a pad may also provide impedance matching."
  
 
+
== Do It Yourself ==
 +
<blockquote>
 +
A quality inline pad can be easily soldered [makes no sense to spend extra money here]:
 +
Insert 3 resistors into your mic cable:
 +
* 2x 470 ohms, inserted into line 2+3 [absolute value +/- 10%, but matched to less than 1% tolerance]
 +
* 1x 470 ohms, inserted between pin 2+3 on the console side.
 +
</blockquote>
 +
Source: [http://www.neumann.com/forums/view.php?bn=neumann_micrec&key=1122644079&v=f Martin Schneider / neumann Mic. Development] 
  
  

Revision as of 19:34, 27 July 2008

Q: What is a Pad?

A "pad" is short for an "Attenuation Pad".

This is a device used to lower the signal level between two other devices.

Padding PS1 Power Stand (Classic) / Model I Inputs

We use pads with our PS1 Power Stand (Classic) / Model Is when running a pro level +4 dBu signal (e.g. output from a mixer) to the XLR inputs on Channels 1 or 2. We want to do this because the input sensitivity for these inputs is set for microphones. To get a better match for levels between the source and our inputs, we can use a pad.

Pads can also help when connecting the PS1 Line Outs to semi-pro or consumer recording devices. If the PS1 Line Outs are too hot for the recorder's inputs, a pad can be used to prevent overdriving those inputs into (clipping) distortion.

A -20dB pad is also a good choice when connecting the PS1 Line Outs to a house PA, or other off-stage system. This would ensure that the house mixing console's inputs can handle the signal level without being overdriven into distortion, especially if the house console has insufficient built-in pads, or none at all. (Beware of the potential for Ground Loops here.)

Daisy Chaining PS1 Power Stand (Classic) / Model Is

Another application (although relatively rare) is if you want to connect the output of one PS1 Power Stand (Classic) / Model I to input of another. Sometimes called daisy chaining, you can connect the Line-Out of one PS1 Power Stand (Classic) / Model I to Channel 1 or 2 of another. In that case you probably want to have a -20 dB pad inline, between the Line-Out of the first System and the Channel 1 or 2 XLR input of the second. See PS1 Powerstand / Daisy Chain for more information.

You can find separate attenuation pads like this:

Pad.jpg

Cost: $20-30 on the web

Sources:

This an example, and you will want to look into the details to determine if you need a pad, and the kinds of connections that are appropriate for your input device.

More Formal Definitions

"attenuator or attenuator pad Electronics. A passive network that reduces the voltage (or power; see usage note under gain) level of a signal with negligible distortion, but with insertion loss. Often a purely resistive network, although any combination of inductors, resistors and capacitors are possible, a pad may also provide impedance matching."

Do It Yourself

A quality inline pad can be easily soldered [makes no sense to spend extra money here]: Insert 3 resistors into your mic cable:

  • 2x 470 ohms, inserted into line 2+3 [absolute value +/- 10%, but matched to less than 1% tolerance]
  • 1x 470 ohms, inserted between pin 2+3 on the console side.

Source: Martin Schneider / neumann Mic. Development


References: