Search results

Jump to: navigation, search

Page title matches

  • When talking about cables the terms Stereo, Mono, Balanced, Unbalanced refer to applications (how a cable is being used). ...end up with poor results. For example, if you connect a stereo signal to a balanced input, you may hear very little, or just effects with none of the original
    8 KB (1,267 words) - 17:43, 7 February 2023
  • [[Image:XLR Male to TRS.jpg|200px|TRS Male to XLR Male balanced cable]]
    248 bytes (40 words) - 15:11, 13 March 2008
  • {{:Balanced vs Unbalanced}}
    27 bytes (3 words) - 11:03, 19 March 2015

Page text matches

  • When talking about cables the terms Stereo, Mono, Balanced, Unbalanced refer to applications (how a cable is being used). ...end up with poor results. For example, if you connect a stereo signal to a balanced input, you may hear very little, or just effects with none of the original
    8 KB (1,267 words) - 17:43, 7 February 2023
  • ...uts are either balanced (three conductors) or unbalanced (two conductors). Balanced signals have the potential to be more resistant to hum and noise. * XLR, male (prongs) and female (receptacles for prongs), usually balanced
    4 KB (654 words) - 10:36, 5 November 2010
  • You can use TS (Tip-Sleeve) unbalanced cables, OR TRS (Tip-Ring-Sleeve) balanced cables. If the cable uses ¼ inch jack plugs and the ends are the sam ==== ¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced) ====
    3 KB (394 words) - 22:20, 16 November 2019
  • === XLR Balanced +4 === === XLR Balanced with built-in-pad ===
    2 KB (372 words) - 02:49, 21 December 2008
  • The {{Model II nl}} Analog Input is balanced and accepts balanced or unbalanced ¼ inch jacks. * Monitor Out — balanced ¼ inch jack outputs
    3 KB (472 words) - 05:04, 21 December 2008
  • === XLR Balanced +4 === ==== XLR (balanced) to XLR (balanced) ====
    2 KB (392 words) - 02:59, 21 December 2008
  • * All XLR outputs are balanced, line-level * All XLR inputs are balanced, microphone level (not a good match for the Kemper XLR outputs)
    5 KB (706 words) - 01:49, 5 January 2023
  • =====¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced) ===== =====¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced) =====
    4 KB (558 words) - 06:14, 3 February 2015
  • What does it mean to have "balanced" vs. "unbalanced" cables and connections? ...d "ground". That's why a "balanced" system (balanced output, 3-wire cable, balanced receiving input) can be better at rejecting any "noise" which might exist b
    8 KB (1,420 words) - 22:59, 18 July 2007
  • ;Balanced connections. '''For best results use a balanced connection
    6 KB (1,027 words) - 13:37, 29 October 2019
  • ...Radial PRODI for the electric organ. I recommend a balanced line-level to balanced line-level direct box for the L1™ inputs. The Radial Twin ISO is a two c ...ise currents. This is one reason for the bad reputation sometimes given to balanced interconnect.
    8 KB (1,303 words) - 09:31, 7 April 2019
  • This mixer has ¼ inch jack balanced outputs. Any of the cables shown below should work. ===== ¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced) =====
    2 KB (250 words) - 14:02, 19 September 2012
  • ...anced, it's usually okay to use a Tip-Sleeve cable. If that connection is balanced, then a Tip-Ring-Sleeve cable is a better choice. If you don't know for sur ...-Ring-Sleeve cable from the S1 Pro system Line Out, then the connection is balanced.
    3 KB (500 words) - 22:20, 16 November 2019
  • The L1 Model II Analog Inputs are 1/4 inch (6.3 mm) Tip-Ring-Sleeve balanced inputs. ...e refer to the owners guide for your mixer to determine if the outputs are balanced.
    2 KB (300 words) - 21:45, 15 September 2022
  • ;For best results for long cable runs, use a Line Level balanced connection ;Note: The 1/4 inch (6.3 mm) Tip-Ring-Sleeve inputs are line-level balanced. <br>
    3 KB (516 words) - 01:51, 5 January 2023
  • * differences in wiring or connectors (e.g. Balanced [[XLR]] to Unbalanced 1/4" [[TRS|Tip-Sleeve]]) 2. Unbalanced to balanced conversion.
    4 KB (608 words) - 15:46, 23 January 2013
  • === XLR Balanced with built-in-pad === === XLR Balanced +4 ===
    2 KB (249 words) - 03:20, 21 December 2008
  • === XLR Balanced +4 === === XLR Balanced with built-in-pad ===
    960 bytes (121 words) - 03:09, 21 December 2008
  • ...line external source. The voltage is equal on Pin 2 and Pin 3 of a typical balanced, XLR-type connector. For a 48 volt phantom source, for example, Pin 2 is 48 ...age to a dynamic microphone even if it is shorted or miswired. In general, balanced dynamic microphones can be connected to phantom powered mixer inputs with n
    8 KB (1,252 words) - 19:43, 10 March 2020
  • == Is the 1/8 inch jack Stereo or Balanced == The {{Compact}} Channel 2: 1/8-inch jack is STEREO not BALANCED.
    811 bytes (106 words) - 06:42, 26 March 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)