Difference between revisions of "Parametric EQ / Solving Problems"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m (formatting)
(added Hilmar's notes)
Line 5: Line 5:
  
 
Chuck-at-Bose provided this approach.<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=1661015674#1661015674 Chuck-at-Bose talks about using the Para EQ to solve a problem frequency]</ref>
 
Chuck-at-Bose provided this approach.<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=1661015674#1661015674 Chuck-at-Bose talks about using the Para EQ to solve a problem frequency]</ref>
=== Width Control ===
+
<table><tr><td valign="top">
Set the '''Width''' control to a value that's narrow enough to zoom in on the problem area, but wide enough to easily hear the effect of coarse adjustments. A value between one third (0.33) and one half (0.50) of an octave often works well as a starting point.
+
# Set the '''Width''' control to a value that's narrow enough to zoom in on the problem area, but wide enough to easily hear the effect of coarse adjustments. A value between one third (0.33) and one half (0.50) of an octave often works well as a starting point.<br />
 +
# Boost (turn up) the '''Level''' control a little, usually about +3 to +6 dB, so that coarse frequency adjustments (next step) can be easily heard.<br />
 +
# Rotate the '''Freq control''' to slowly sweep across the spectrum. Start low and sweep up until you hear the offending note jump out. Go back and forth until the problem note is centered, or at its loudest. For problem note, the frequency of the B flat note is approximately 58 Hz.<br>
 +
</td>
 +
<td>
 +
[[Image:T1ParaEQCN01.png]]
 +
</td>
 +
</tr>
 +
<tr>
 +
<td valign="top">
 +
# Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes. <br />
 +
# Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of    -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.
 +
</td>
 +
<td>
 +
[[Image:T1ParaEQCN02.png]]
 +
</td>
 +
</tr>
 +
</table>
 +
 
 +
=== Another Approach ===
 +
Hilmar-at-Bose had a different approach<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/6531054674?r=7421005674#7421005674  Hilmar-at-Bose talks about solving a boomy note]</ref>
 +
 
 +
Here is one method to eliminate a boomy note
 +
 
 +
a) set the level of the para EQ to a cut, say -10 dB
 +
b) set the width to fairly narrow, say .25 octaves
 +
c) start with a rough estimate of the offending frequency and then move the frequency around until the offending note gets tamed best
 +
d) you can press on the level control to toggle between on and off which gives you a direct A/B so you can judge the effect better
 +
 
 +
Once you have centered on the frequency you adjust the level and width to taste.
  
=== Level Control ===
+
Estimating the frequency:
Boost (turn up) the '''Level''' control a little, usually about +3 to +6 dB, so that coarse frequency adjustments (next step) can be easily heard.
+
* Low octave of the bass is from 40 Hz to 80 Hz (E1 to E2), A1 is at 55 Hz
 +
* Low octave on the guitar is from 80 Hz to 160 Hz (E2 to E3), A2 is at 110 Hz
 +
* 2nd octave on the guitar is from 160 Hz to 320 Hz (E3 to E4), A3 is at 220 Hz
  
=== Freq Control ===
+
Here is a cheat sheet http://www.phy.mtu.edu/~suits/notefreqs.html
Rotate the '''Freq control''' to slowly sweep across the spectrum. Start low and sweep up until you hear the offending note jump out. Go back and forth until the problem note is centered, or at its loudest. For Jim's example above, the frequency of the B flat note is approximately 58 Hz.
 
  
[[Image:T1ParaEQCN01.png]]
+
Hope that helps
  
=== Width Control ===
+
Hilmar
Adjust the '''Width''' control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to ''one fifth'' (0.20) of an octave, which is great for 'notching out' problem notes.
 
  
=== Level Control ===
 
Now adjust the '''Level'' control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of    -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.
 
  
[[Image:T1ParaEQCN02.png]]
 
  
 
----
 
----
 
<references />
 
<references />
 
[[Category:T1]]
 
[[Category:T1]]

Revision as of 16:31, 10 July 2007

Troubleshooting with the T1 ToneMatch Audio Engine Parametric EQ

Using Para EQ to solve a problem frequency

In this example a Bassist was having a problem with a resonant note (B flat).

Chuck-at-Bose provided this approach.[1]

  1. Set the Width control to a value that's narrow enough to zoom in on the problem area, but wide enough to easily hear the effect of coarse adjustments. A value between one third (0.33) and one half (0.50) of an octave often works well as a starting point.
  2. Boost (turn up) the Level control a little, usually about +3 to +6 dB, so that coarse frequency adjustments (next step) can be easily heard.
  3. Rotate the Freq control to slowly sweep across the spectrum. Start low and sweep up until you hear the offending note jump out. Go back and forth until the problem note is centered, or at its loudest. For problem note, the frequency of the B flat note is approximately 58 Hz.

T1ParaEQCN01.png

  1. Adjust the Width control to as narrow a value as possible, so that only the problem is being affected, leaving the non-offending frequencies around it unchanged. The T1 goes down to one fifth (0.20) of an octave, which is great for 'notching out' problem notes.
  2. Now adjust the 'Level control to cut (turn down) enough to make the problem go away, but not so much that the tone of the source is altered in an undesirable way. Values of -1 to -6 dB will often do the trick, though sometimes a more aggressive cut is necessary. Use your ears to find an appropriate balance between fixing the problem and adversely altering the tone of the source.

T1ParaEQCN02.png

Another Approach

Hilmar-at-Bose had a different approach[2]

Here is one method to eliminate a boomy note

a) set the level of the para EQ to a cut, say -10 dB b) set the width to fairly narrow, say .25 octaves c) start with a rough estimate of the offending frequency and then move the frequency around until the offending note gets tamed best d) you can press on the level control to toggle between on and off which gives you a direct A/B so you can judge the effect better

Once you have centered on the frequency you adjust the level and width to taste.

Estimating the frequency:

  • Low octave of the bass is from 40 Hz to 80 Hz (E1 to E2), A1 is at 55 Hz
  • Low octave on the guitar is from 80 Hz to 160 Hz (E2 to E3), A2 is at 110 Hz
  • 2nd octave on the guitar is from 160 Hz to 320 Hz (E3 to E4), A3 is at 220 Hz

Here is a cheat sheet http://www.phy.mtu.edu/~suits/notefreqs.html

Hope that helps

Hilmar