View source for T1 ToneMatch® Audio Engine / Aux

[[Image:T1Aux.png|right]]
The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. Tap points where you can set the output to the Aux.<ref name="AuxTap">Aux Tap Points from page 26 of the {{T1 Manual}}</ref>

* Dry: After Preamp: The completely dry (no processing) signal is routed directly from the preamp stage.
* Pre: With EQ & FX: The signal is routed from the preamp stage with applied processing.
* Post: After Fader: The signal is routed after the Channel volume control with applied processing.

Excerpt from the T1™ Manual
----
[[Image:T1ManualP26AuxRouting.png]]
----



=== No Reverb on Aux ===
Q: Why is there no Reverb on the Aux output of the {{T1}}?

A: Hilmar-at-Bose writes<ref>Hilmar-at-Bose writes about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/4091082864?r=8551095774#8551095774 No Reverb on Aux]</ref>
: The {{T1}} has lots of different effects units and normally they are unique to each channel. That means that the T1™  has 4 individual dynamic processors, 4 modulators (chorus flanger, phaser, etc.) , 4 EQs, 4 delay processors, etc. The only exception is the reverb, which is shared by all channels. <br />
:The AUX is also a per-channel control. That means if you turn up the AUX of channel, you expect to hear signals from channel 1 and only from channel 1. However, the output of the reverb processor contains the reverb portions of all 4 channels. If we add that to the Aux, you'd hear the reverb portions of all 4 channels and not only the channel that you are interested in. In most cases, this is probably not what you want.<br />
:If you are familiar with conventional mixing consoles, you will find that the situation is quite similar. You can only route to an AUX output effects that are specific to a channel (normally these would be connected to the insert loop of this channel). The "shared" effects typically come into the board through an AUX return, which is not channel specific.

The discussion continues in the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/4091082864?r=8551095774#8551095774 Message Board]

Reference: page 52 of the {{T1 Manual}}

Problem: Aux output does not sound right.

What To Do:
* Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input signals to the Aux output” on page 26.<ref name="AuxTap">Routing input signals to the Aux output on page 26 of {{T1 Manual}}</ref>

Note: No reverb comes from the Aux output even if the tap point is Pre or Post.

* Verify that each input assigns the desired signal level to the Aux output.
=== Aux to a separate System ===
To direct an input exclusively to Aux see: [[T1 ToneMatch™ Audio Engine / Aux to a Separate System]]


<!-- preparation for more notes about using T1™ connected to two Power Stands -->
<!--
Originally posted by BlackForestMan:
As  [b]separation of musical sources (voc or instrument) on several L1[/b] is one of other great advantages of the BOSE  L1-System, that  [b]is what I try to do whenever possible[/b].
And that's what I tried to do with  [b]one T1 for two (or three) musicians[/b].

In the meantime I've found a way how to  [b]use the ch-vol knob to control the aux path[/b], with very very few (hardly noticeable) signal on the master out path, by putting the AUX-Mix to 100% and reducing the trim for this channel.

So it's almost perfect for me, besides the missing reverb on aux out.

Wolfgang[/QUOTE]

See it [url=http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/4091082864?r=8791046974#8791046974]in context[/url] 

 A note about the missing reverb on aux out.  Wolfgang is correct. There is no reverb on aux out. For details see:

[url=http://toonz.ca/bose/wiki/index.php?title=T1_ToneMatch%E2%84%A2_Audio_Engine/Aux]No Reverb on Aux[/url] 
-->


<!-- end preparation -->

<noinclude>
----
<references />
[[Category:T1]]
[[Category:T1Aux]]
</noinclude>