Difference between revisions of "T1® to Denon DN-X500"
m (→{{T1}} to Denon DN-X500 microphone input) |
m (ST moved page T1® to Denon DN-X500 to T1® to Denon DN-X500) |
||
| (3 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
T1® to Denon DN-X500 | T1® to Denon DN-X500 | ||
| − | + | Connecting an {{T1}} to a Denon DN-X500. There are three connections on the Denon DN-X500 where you could connect a {{T1}} Master or Aux output. | |
| + | |||
| + | |||
| + | ==== Notes that apply to all three approaches ==== | ||
| + | You'll need a [[T1_ToneMatch%C2%AE_Audio_Engine_power_supply|T1 ToneMatch%C2%AE Audio Engine power supply]][[Image:T1_power_supplyThumb.jpg]] | ||
| + | |||
| + | The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control to get a good level match to the input that you use on the Denon-DNX500. | ||
| + | |||
| + | Make the connection with a ¼ inch jack Tip-Ring-Sleeve cable. | ||
| + | |||
| + | [[Image:TrsMtrsM.png]] | ||
| − | |||
==== {{T1}} to Denon DN-X500 microphone input ==== | ==== {{T1}} to Denon DN-X500 microphone input ==== | ||
| Line 13: | Line 22: | ||
[[Image:DN-X500Input4T1.png]] | [[Image:DN-X500Input4T1.png]] | ||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
Latest revision as of 03:25, 26 March 2017
T1® to Denon DN-X500
Connecting an T1 ToneMatch Audio Engine to a Denon DN-X500. There are three connections on the Denon DN-X500 where you could connect a T1 ToneMatch Audio Engine Master or Aux output.
Contents
Notes that apply to all three approaches
You'll need a T1 ToneMatch%C2%AE Audio Engine power supply
The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control to get a good level match to the input that you use on the Denon-DNX500.
Make the connection with a ¼ inch jack Tip-Ring-Sleeve cable.
T1 ToneMatch Audio Engine to Denon DN-X500 microphone input
The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control.
The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
T1 ToneMatch Audio Engine to Denon DN-X500 microphone input
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
This is a screen shot of English page 3 with an overlay of the back of the T1® ΞΘ∞∋--
T1 ToneMatch Audio Engine to Denon DN-X500 Effects Return
This could give you a better match for levels and impedance, but you will have to control everything with the T1®. Start with the master output of the T1® all the way off and bring it up slowly.
Reference Notes: Denon DN-X500 User Manual
http://usa.d-mpro.com/DocumentMaster/US/f1160bc969bf42e0bc5e90b6600c5207.pdf