Template:T1 to Model I or Classic: Difference between revisions
(First edition of this template (material appeared in article before)) |
m (added the documentation about the change to documentation (use 3 for input level)) |
||
| Line 50: | Line 50: | ||
[[Image:T12ModelI.png]] | [[Image:T12ModelI.png]] | ||
With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote. | |||
The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag. | |||
=== Input setting recommendation now '''3''' === | |||
<section begin=InputSettingNow3 /> | |||
MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this. | |||
For these conditions: | |||
{{Classic icon}}{{Model I icon}} | |||
* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4 | |||
* Balanced OR Unbalanced 1/4" cable | |||
* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock | |||
* Proper gain staging required on the T1® itself | |||
I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions. | |||
This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}. | |||
If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®. | |||
<section end=InputSettingNow3 /> | |||
Hopefully this is helpful - please ask away with any questions for clarification. | |||
MikeZ | |||
Revision as of 02:51, 15 January 2009
Here are details on how to connect a T1 ToneMatch Audio Engine to a L1 Classic or L1 Model I
Notes:
The recommended trim setting input Ch 3 or Ch 4 is 3 (see below).
With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote. More on this later.
For these conditions:
- T1 ToneMatch® Audio Engine going into L1® Model I/L1® Classic into Channel 3/4
- Balanced OR Unbalanced 1/4" cable
- Remote unplugged, OR, master volume on Remote at 12 o clock
- Proper gain staging required on the T1® itself
This will give you the same gain going into the L1® Model I/L1® Classic as if you were going through the ToneMatch® input on a L1 Model II.
If you are using the Remote on your L1® Model I/L1® Classic, then you will need to compensate a bit. If you are running the Remote master volume at max, then stick with 2 on Ch 3/4. When using a T1®, run the master volume of the R1 above 12 o'clock .
Connection to L1 Model I / L1 Classic with Remote
If you want to use the PS1 Power Stand Channels 1 or 2 or 4, then you will want to connect the R1 Remote to the PS1 Power Stand.
Excerpt from the T1 ToneMatch Audio Engine Manual - page 20 - Note: this recommended input setting is now 3. See the note above.
With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
The T1 ToneMatch Audio Engine controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.
Input setting recommendation now 3
MikeZ-at-Bose wrote[1] Bill-at-Bose and I have revisited this.
For these conditions:
- T1 ToneMatch® Audio Engine going into L1® Model I/L1® Classic into Channel 3/4
- Balanced OR Unbalanced 1/4" cable
- Remote unplugged, OR, master volume on Remote at 12 o clock
- Proper gain staging required on the T1® itself
I'm going to revise the original recommendation of 2 for Ch 3/4 to 3 - under the above conditions.
This will give you the same gain going into the L1® Model I/L1® Classic as if you were going through the ToneMatch® input on a L1 Model II.
If you are using the Remote on your L1® Model I/L1® Classic, then you will need to compensate a bit. If you running the Remote master volume at max, then stick with 2 on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.
Hopefully this is helpful - please ask away with any questions for clarification.
MikeZ
- ↑ MikeZ-at-Bose talks about the input setting on the L1® Model I or L1® Classic Power Stand with the T1®