Difference between revisions of "Microphone Feedback"
(continuing to edit...) |
(cleaning up) |
||
| Line 12: | Line 12: | ||
* If you are using vocal effects like reverb, chorus or delay, turn them off until you can get sufficient [[Gain Before Feedback|gain before feedback]] to get performance level volume. Then add the effects back into the signal chain (one at a time) so you can be aware of the individual impacts that each effect is having on feedback. | * If you are using vocal effects like reverb, chorus or delay, turn them off until you can get sufficient [[Gain Before Feedback|gain before feedback]] to get performance level volume. Then add the effects back into the signal chain (one at a time) so you can be aware of the individual impacts that each effect is having on feedback. | ||
| − | * Get close to the microphone. No other technique has a big an impact on feedback. Each halving of distance is approximately another 6 dB of [[gain before feedback]]. This means that the difference between working a microphone at 2 inches, and 1/4 inch is 18 dB, which is more than twice as loud. | + | * '''Get close to the microphone''' when you want to be loud. No other technique has a big an impact on feedback. Each halving of distance is approximately another 6 dB of [[Gain Before Feedback|gain before feedback]]. This relationship in physics is known as the [[Inverse Square Law]]. This means that the difference between working a microphone at 2 inches, and 1/4 inch is 18 dB, which is more than twice as loud. While good mic technique often involves "working" the microphone at different distances, singers must be mindful of the fact that small changes in distance from the mouth result in very dramatic changes in sound level. |
[[Image:Ferrin_eat_mic.jpg|Charlie Ferrin at Bose: Nov. 9, 2007]] | [[Image:Ferrin_eat_mic.jpg|Charlie Ferrin at Bose: Nov. 9, 2007]] | ||
| Line 26: | Line 26: | ||
* Use the high-frequency tone control for the microphone channel carefully. Feedback could occur when this is set too high. | * Use the high-frequency tone control for the microphone channel carefully. Feedback could occur when this is set too high. | ||
| − | [ | + | * Wherever possible, acoustic instruments should use pickups instead of microphones. Pickup systems provide much higher [[Gain Before Feedback|gain before feedback]] than microphones. |
| − | * | + | === Techniques specific to the {{L1 family}} === |
| + | * All players should be playing / singing through the {{L1}} closest to them. | ||
| − | |||
| − | + | == Other Resources == | |
| − | + | * [http://www.shure.com/stellent/groups/public/@gms_gmi_web_ug/documents/web_resource/us_pro_mics_for_music_sound_ea.pdf Shure® article on mic technique] Shure Educational Publication 2006 39 pages - pdf format | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
---- | ---- | ||
<references/> | <references/> | ||
Revision as of 11:31, 4 January 2009
Proper Gain Staging is essential to avoiding feedback. Please take 2 minutes to review this short video. Although this is based on the Classic and Model I, the principles are generally applicable.
Contents
Gain Staging
Take two minutes to watch this video by clicking on the picture.
If you are using an L1 Classic or L1 Model I follow the instructions exactly as Steve says. For other L1 models, the principles are still applicable.
Gain setup for a vocal microphone
Techniques For Reducing Feedback
- If you are using vocal effects like reverb, chorus or delay, turn them off until you can get sufficient gain before feedback to get performance level volume. Then add the effects back into the signal chain (one at a time) so you can be aware of the individual impacts that each effect is having on feedback.
- Get close to the microphone when you want to be loud. No other technique has a big an impact on feedback. Each halving of distance is approximately another 6 dB of gain before feedback. This relationship in physics is known as the Inverse Square Law. This means that the difference between working a microphone at 2 inches, and 1/4 inch is 18 dB, which is more than twice as loud. While good mic technique often involves "working" the microphone at different distances, singers must be mindful of the fact that small changes in distance from the mouth result in very dramatic changes in sound level.
- Use a directional microphone. Hypercardioid is better than cardioid, which is better than omnidirectional. All sound waves impinging on the microphone from a direction other than the intended signal is "noise" and will lower the threshold of feedback.
- Use as few open microphones as possible. When a microphone is not in use, if possible, turn it off.
- When stand mounting a directional microphone, tilt the microphone up ten or twenty degrees off the horizon so that it is less sensitive to direct sound from the speakers.
- Use the high-frequency tone control for the microphone channel carefully. Feedback could occur when this is set too high.
- Wherever possible, acoustic instruments should use pickups instead of microphones. Pickup systems provide much higher gain before feedback than microphones.
Techniques specific to the L1 family of products
- All players should be playing / singing through the L1 closest to them.
Other Resources
- Shure® article on mic technique Shure Educational Publication 2006 39 pages - pdf format