Difference between revisions of "B1 Cable Connections"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
(first edition)
 
m (B1/B2)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
<b>''' B1 Cable - Connections'''</b>
+
<noinclude>__TOC__  <!-- setup for transclusion --> </noinclude>
 +
=== B1/B2 Cable - Connections ===
 +
From Kyle-at-Bose <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6251023092/r/9601083192#9601083192 B1 Cable Connections]</ref>
  
We've seen some past B1 cable quality problems which, because of input from folks like yourself, we've since resolved.
+
We've seen some past B1 cable quality problems which, because of input from folks like you, we've since resolved.
  
 
I'm fairly confident that the connector and wires in the cable assembly are OK. The problems we were having were related to the actual connection of the wire leads to the Speakon connector. Problems would be obvious in one case- the bass module cuts out. The second case would not be so obvious- the EQ to the B1 and L1 would be wrong and would make the system perform and sound poor.
 
I'm fairly confident that the connector and wires in the cable assembly are OK. The problems we were having were related to the actual connection of the wire leads to the Speakon connector. Problems would be obvious in one case- the bass module cuts out. The second case would not be so obvious- the EQ to the B1 and L1 would be wrong and would make the system perform and sound poor.
Line 9: Line 11:
 
Remove the rear shell of the connector by unscrewing it. (See the pic below, not the exact connector but similar). We use a 4-wire connection so what you need to do is re-attach, possibly restripping first (need to use a wire stripper), the wire to the connector terminals. There are four terminals +1, -1, +2, -2. Each wire needs to be appropriately connected to the same terminal on each end of the cable. Luckily, no soldering is needed. These Speakon connectors have screw terminals. All you need to do is unscrew the terminal using a screwdriver, reinsert the bare wire, and then tighten the terminal.  
 
Remove the rear shell of the connector by unscrewing it. (See the pic below, not the exact connector but similar). We use a 4-wire connection so what you need to do is re-attach, possibly restripping first (need to use a wire stripper), the wire to the connector terminals. There are four terminals +1, -1, +2, -2. Each wire needs to be appropriately connected to the same terminal on each end of the cable. Luckily, no soldering is needed. These Speakon connectors have screw terminals. All you need to do is unscrew the terminal using a screwdriver, reinsert the bare wire, and then tighten the terminal.  
  
If you have any questions about this, don't hesitate to ask!
+
[[Image:SpeakonExplodedNL4.gif]]
 +
 
 +
=== B1/B2 Conductors Broken ===
 +
From Harry (dancingdogmuse)<ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/8331099664?r=2951007864#2951007864 L1 Classic Failure]</ref>
 +
 
 +
The initial symptoms were clicking followed by silence. It turned out to be a problem with broken wires inside the blue jacket of the B1 cable.
 +
 
 +
 
 +
[[Image:Bose B1 cableDamage1.JPG]]
 +
 
  
Kyle-at-Bose <ref>[http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/6251023092/r/9601083192#9601083192 B1 Cable Connections]</ref>
+
[[Image:Bose B1 cableDamage2.JPG]]
  
[[Image:SpeakonExplodedNL4.gif]]
 
  
  
---
+
<noinclude>
 
<references/>
 
<references/>
[[category:B1 Base Module]]
+
[[Category:B1 Bass Module]]
 +
 
 +
[[Category:B2 Bass Module]]
 +
</noinclude>

Latest revision as of 05:00, 15 December 2012

B1/B2 Cable - Connections

From Kyle-at-Bose [1]

We've seen some past B1 cable quality problems which, because of input from folks like you, we've since resolved.

I'm fairly confident that the connector and wires in the cable assembly are OK. The problems we were having were related to the actual connection of the wire leads to the Speakon connector. Problems would be obvious in one case- the bass module cuts out. The second case would not be so obvious- the EQ to the B1 and L1 would be wrong and would make the system perform and sound poor.

So, if you have a moment and a screwdriver, we can fix these cables together.

Remove the rear shell of the connector by unscrewing it. (See the pic below, not the exact connector but similar). We use a 4-wire connection so what you need to do is re-attach, possibly restripping first (need to use a wire stripper), the wire to the connector terminals. There are four terminals +1, -1, +2, -2. Each wire needs to be appropriately connected to the same terminal on each end of the cable. Luckily, no soldering is needed. These Speakon connectors have screw terminals. All you need to do is unscrew the terminal using a screwdriver, reinsert the bare wire, and then tighten the terminal.

SpeakonExplodedNL4.gif

B1/B2 Conductors Broken

From Harry (dancingdogmuse)[2]

The initial symptoms were clicking followed by silence. It turned out to be a problem with broken wires inside the blue jacket of the B1 cable.


Bose B1 cableDamage1.JPG


Bose B1 cableDamage2.JPG