Dual Mono

From Bose Portable PA Encyclopedia
Revision as of 08:57, 27 March 2019 by ST (talk | contribs) (Dual Mono: {{Two L1 Systems}})
Jump to: navigation, search

L1 Model II This information is applicable to the L1®  Model II
L1 Compact



This article pertains to Dual Mono with L1 systems.

L1 Systems

The L1 systems have extremely wide horizontal dispersion. As a result, running multiple L1 systems in the same sound field may result in overlap. The comments below are applicable in that context.

Non-L1 Systems

The F1 Model 812 Flexible Array Loudspeaker and S1 Pro System systems have narrower horizontal dispersion. If you space those systems apart or aim them to avoid overlap, this article is not applicable.

Dual Mono

This is amplifying the same sound source through two separate loudspeakers. 

Hilmar-at-Bose wrote:

Dual mono (with the L1 systems) is usually not a good idea, if you have more than one performer. With more than one performer/source it's in my opinion always preferable to separate the sources (i.e. one source per L1). The spatial separation and precise localization help more with clarity much more than the added gain.
For a single performer/single source it's not quite so clear cut. One will be more accurate (i.e. sound is clearly located at the performer's position, more consistent spectrum) and two will sound wider and more spacious. In the end, that is an artistic decision, depending on which one is closer to your artistic intent.
-- Source Dual mono is usually not a good idea

Benefits of Two L1 Systems

L1 Model II This information is applicable to the L1®  Model II
L1 Model 1S This information is applicable to the L1®  Model 1S
L1 Compact

This discussion pertains to using two L1 systems with the same sound source (Dual Mono). For a discussion about stereo see Stereo / Mono / Distributed Systems
What is the benefit of using two L1 systems over one?
You will get more coverage (based on the distance between the L1 systems) and an increase in loudness (but not double the loudness)[1] .
How much more coverage will I get?
The increased coverage will be the result of the distance between the two systems. For example, if you place them twenty feet apart in the horizontal plane, you will get twenty feet more coverage from side to side. You will also increase the overall sound level by +3 dB. Your projection straight ahead may improve but that is harder to predict as the distances increases.
How much gain do you get when you run two L1 systems with the same source?
Short answer: +3 dB in practice
+6 dB in theory

The most you can ever get from putting two sources fed by the same signal together is +6 dB. The reason?

  • Sound waves add in space through the principle of superposition. If the waves from two sources perfectly add, you get twice the amplitude, which is +6 dB.
  • To get the full +6 dB the two sources have to be spaced very closely together relative to a wavelength of sound. at 50 Hz, where the wavelength of sound is about 20' (about 7 meters) that's pretty easy to do. Massing your bass modules is done for this reason -- to get the 6 dB per doubling of bass module systems. But at 1,000 Hz, where the wavelengths are 12 inches (about 30 cm) you just can't do get L1 speakers close enough. As a result, you get something less than 6 dB because at some angles instead of the sound waves constructively adding they will destructively cancel (one will be partly or completely out of phase with the other).
+3 dB in practice

Once you separate the sources by several or more wavelengths, the summations and cancellations are so numerous and so complex that we say the two sources are essentially uncorrelated (not strictly true, but for the purposes of this argument, a very close approximation.) When two sources are uncorrelated the only thing you can count on is that the total amount of acoustic power going into the room will be doubled. Doubling the power is +3 dB.

Is +3 dB twice as loud?
  • Doubling the power (+3 dB)is not twice as loud.
  • A non-exact rule-of-thumb is that every 10 dB increase is a doubling of perceived loudness. [1]
  1. Put bass modules together if you can because they'll give you an honest 6 dB per doubling of bass modules/
  2. If you are sending a mono or stereo signal to spaced L1 systems, try to space them 20 feet (7 meters) or more if you can because this will minimize any audible cancellations.

Related reading