Difference between revisions of "Mixer"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m (XLR (balanced) to XLR (balanced))
m (XLR to XLR)
Line 27: Line 27:
  
 
==== XLR to XLR  ====
 
==== XLR to XLR  ====
 +
[[Image:XLRXLRMF.png|thumb|XLR to XLR, male to female|right]]
 +
This is the same kind of cable you would use to connect a microphone.
 +
 +
The XLR inputs for Channels 1 and 2 are intended for microphone level inputs. <br>
  
The XLR inputs for Channels 1 and 2 are intended for microphone level inputs. <br>
 
 
==== XLR (balanced) to XLR (balanced)  ====
 
==== XLR (balanced) to XLR (balanced)  ====
  

Revision as of 12:32, 1 November 2010


Alesis MultiMix8USBBehringer UB1202Mackie 1202 VLZ ProNumark CD Mix-2Spirit NotepadYamaha MG82/FX

Mixers

General Notes

L1 Model I and L1 Classic

L1 Model I This information is applicable to the L1 Model I
Classic This information is applicable to the L1® Classic

¼ inch jack inch to ¼ inch

If your mixer has ¼ inch jack outputs, these are almost certainly at line-level and should work well with any of the ¼ inch jack inputs (Channels 1, 2, 3, 4) on a L1 Model I or L1 Classic.

¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

Tip-Sleeve to Tip-Sleeve

This should work fine.

¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)

Tip-Ring-Sleeve to Tip-Sleeve

This should work fine.

¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

Tip-Ring-Sleeve to Tip-Ring-Sleeve

This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.

XLR to XLR

XLR to XLR, male to female

This is the same kind of cable you would use to connect a microphone.

The XLR inputs for Channels 1 and 2 are intended for microphone level inputs.

XLR (balanced) to XLR (balanced)

  • If your source (mixer or CD/DVD player) has XLR outputs, check to see if you have the option to set it to a microphone level output. If so, use that setting.
  • If your source has XLR outputs at line-level (most likely) then you will probably need a Pad between the source and the L1 Model I (or L1 Classic) Power Stand.
  • You may be able to make things work without the Pad by turning down the output from the source and turning down the trim at the Power Stand. If it sounds okay then you are probably fine. If you cannot get enough a good sounding signal without an excess of noise then try a Pad.

L1 Model II

L1 Model II This information is applicable to the L1®  Model II

A ¼ inch Tip-Ring-Sleeve connector carrying a stereo signal should not be used with the analog input on the Model II.

Even though a ¼ inch Tip-Ring-Sleeve connector can carry a stereo signal this is not how this physical connection is used on the Mixer Power Stand.

The analog input on the Model II is balanced, and will therefore subtract the Left and Right signals on a stereo cable and you will hear an L-R (Left minus Right) signal in the Model II.

You cannot 'get through the gig' this way if you are a DJ or if you need to run prerecorded music or have stereo inputs.

TRSfromStereoRCAModelII.png

TRSfromStereo14ModelII.png

18stereoTo14stereoModelII.png


Using a Mixer

L1 Model II

Alesis MultiMix8USBBehringer UB1202Mackie 1202 VLZ ProNumark CD Mix-2Spirit NotepadYamaha MG82/FX

If you are using a mixer instead of a T1 ToneMatch Audio Engine use the mixer to create a mono output and send that to the Model II Power Stand Analog input.

  • If there is a stereo/mono switch then use it and send the mono output to the Model II Power Stand Analog input.
  • If there is a Left/mono output then use that and send it to the Model II Power Stand Analog input.
  • If there is no way to create a mono output then pan all your mixer inputs all the way to one side (e.g. Left) and then take the mixer for that side (e.g. Left) output and send it to the Model II Power Stand Analog input.



T1 ToneMatch Audio Engine

T1 This information is applicable to the T1 ToneMatch® audio engine

  • You can run ¼ inch jack line level inputs to T1® Channels 1,2,3.
  • You can probably run XLR line level inputs to the T1® Channels 1,2,3. No Pad required.
T1 ToneMatch® Audio Engine inputs will accept a wide range of signals. We have not encountered a normal use where someone needed a pad - even using +4dbU console outputs[1]
  • If you have the option to run ¼ inch to ¼ inch, you could use T1® Channels 4/5. This would leave more channels available for use with microphones and instruments with lower output levels.

  1. MikeZ-at-Bose talks about T1® inputs in T1® Audio Engine Questions

DJ Mixer vs General Purpose Mixer

The discussion is live: DJ Mixers vs "Band" mixers and at least for now, open to some controversy.




Read about specific mixers in Mixers