Difference between revisions of "PS1 Powerstand Connections / Line Out"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m
m (labelled section transclude correction in syntax)
Line 2: Line 2:
 
{{Classic icon}}{{Model I icon}}
 
{{Classic icon}}{{Model I icon}}
 
== Summary ==
 
== Summary ==
<section start="Connections" />
+
<section start=Connections />
 
=== Line Outs (XLR balanced) for Channels 1 and 2 ===
 
=== Line Outs (XLR balanced) for Channels 1 and 2 ===
 
* post trim (+4 dBu nominal)
 
* post trim (+4 dBu nominal)
Line 29: Line 29:
  
 
See: [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/1431057611?r=1771034582#1771034582 Recording Through the PS1] &mdash; Message Board Discussion.
 
See: [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/1431057611?r=1771034582#1771034582 Recording Through the PS1] &mdash; Message Board Discussion.
<section end="Connections" />
+
<section end=Connections />
 
{{:PS1 Powerstand Connections/Line Out/XLR}}
 
{{:PS1 Powerstand Connections/Line Out/XLR}}
 
{{:PS1 Powerstand Connections/Line Out/Insert}}
 
{{:PS1 Powerstand Connections/Line Out/Insert}}

Revision as of 11:29, 8 July 2010

PS1 Connections Lines Out

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I

Summary

Line Outs (XLR balanced) for Channels 1 and 2

  • post trim (+4 dBu nominal)

Insert Send

  • post trim,
  • post channel volume

SPDIF Data OUT

  • Post trim
    • Input Trim
    • R1 Remote Channel volume
    • Insert returns
  • Pre
    • Preset
    • Tone controls
    • R1 Remote Master volume.
  • SPDIF is channels 1 & 2 only.

The Data OUT is a SPDIF output with a sampling rate of 48KHz.

Set your recording software as below if given the options

  • 24 Bit
  • 48 KHz
  • S/PDIF (RCA)

See: Recording Through the PS1 — Message Board Discussion.

Line Outs (XLR balanced) for Channels 1 and 2

  • post trim (+4 dBu nominal)

For Channels One or Two you can run an XLR cable to the House or recording console like this. The outputs are post-trim (+4 dBu nominal).

PS1LineOutXLR.jpg

This is not suitable for connection to another PS1 Power Stand (Classic) / Model I as the output level is too high for a PS1 Power Stand (Classic) / Model I Channel 1 or 2 input. If you want to connect one L1® to another please see: PS1 Powerstand / Daisy Chain


L1 Model I This information is applicable to the L1 Model I
Classic This information is applicable to the L1® Classic

Line Out from Insert Point

  • access from the "ring" connection at the Insert Point
  • post trim
  • post R1 Remote Channel Level

For Channels One or Two insert a 1/4 inch cable halfway into the Insert jack to get a signal that is controlled by the volume control on the Remote. This is also known as the Half Insert method. For more information about 1/4 cables see Tip Ring Sleeve connections. The rectangular box shown below the input panel is a DI, used to output the signal to a console or house system.

PS1LineOutInsert.jpg



Line Out from Channels 3 or 4

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I

There is no output from the PS1 Power Stand (Classic) / Model I for Channels 3 or 4. To share inputs with an external system use a DI.

PS1LineOutDI.jpg