Difference between revisions of "PS1 Powerstand Connections / Line Out"
(first ed.) |
m |
||
| (18 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | <big>'''PS1 Connections Lines Out '''</big> | + | <noinclude><big>'''PS1 Connections Lines Out '''</big> </noinclude> |
| + | {{Classic icon}}{{Model I icon}} | ||
| + | <noinclude>== Summary == | ||
| + | </noinclude><section begin=Connections /> | ||
| + | <includeonly>==PS1 Connections Lines Out==</includeonly> | ||
| + | === Line Out (XLR balanced) for Channels 1 and 2 === | ||
| + | * post trim (+4 dBu nominal) | ||
| − | + | === Insert Send === | |
| + | * post trim, | ||
| + | * post channel volume | ||
| − | Insert | + | === SPDIF Data OUT === |
| − | + | * Post trim | |
| − | + | ** Input Trim | |
| + | ** R1 Remote Channel volume | ||
| + | **Insert returns | ||
| + | * Pre | ||
| + | ** Preset | ||
| + | ** Tone controls | ||
| + | ** R1 Remote Master volume. | ||
| + | * SPDIF is channels 1 & 2 only. | ||
| − | + | The Data OUT is a SPDIF output with a sampling rate of 48KHz. | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | + | Set your recording software as below if given the options | |
| + | * 24 Bit | ||
| + | * 48 KHz | ||
| + | * S/PDIF (RCA) | ||
| + | See: [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/1431057611?r=1771034582#1771034582 Recording Through the PS1] — Message Board Discussion. | ||
| + | <section end=Connections /> | ||
| + | {{:PS1 Powerstand Connections/Line Out/XLR}} | ||
| + | {{:PS1 Powerstand Connections/Line Out/Insert}} | ||
| + | {{:PS1 Powerstand Connections/Line Out/Channel 3/4}} | ||
---- | ---- | ||
| Line 21: | Line 39: | ||
| − | [[ | + | [[Category:L1® System]] |
[[category:PS1 Powerstand]] | [[category:PS1 Powerstand]] | ||
[[category:PS1 Powerstand Connections]] | [[category:PS1 Powerstand Connections]] | ||
Latest revision as of 10:39, 5 November 2010
PS1 Connections Lines Out
Contents
Summary
Line Out (XLR balanced) for Channels 1 and 2
- post trim (+4 dBu nominal)
Insert Send
- post trim,
- post channel volume
SPDIF Data OUT
- Post trim
- Input Trim
- R1 Remote Channel volume
- Insert returns
- Pre
- Preset
- Tone controls
- R1 Remote Master volume.
- SPDIF is channels 1 & 2 only.
The Data OUT is a SPDIF output with a sampling rate of 48KHz.
Set your recording software as below if given the options
- 24 Bit
- 48 KHz
- S/PDIF (RCA)
See: Recording Through the PS1 — Message Board Discussion.
Line Outs (XLR balanced) for Channels 1 and 2
- post trim (+4 dBu nominal)
For Channels One or Two you can run an XLR cable to the House or recording console like this. The outputs are post-trim (+4 dBu nominal).
This is not suitable for connection to another PS1 Power Stand (Classic) / Model I as the output level is too high for a PS1 Power Stand (Classic) / Model I Channel 1 or 2 input. If you want to connect one L1® to another please see: PS1 Powerstand / Daisy Chain
Line Out from Insert Point
- access from the "ring" connection at the Insert Point
- post trim
- post R1 Remote Channel Level
For Channels One or Two insert a 1/4 inch cable halfway into the Insert jack to get a signal that is controlled by the volume control on the Remote. This is also known as the Half Insert method. For more information about 1/4 cables see Tip Ring Sleeve connections. The rectangular box shown below the input panel is a DI, used to output the signal to a console or house system.
Line Out from Channels 3 or 4
There is no output from the PS1 Power Stand (Classic) / Model I for Channels 3 or 4. To share inputs with an external system use a DI.
