Difference between revisions of "PS1 Powerstand Connections / Line Out"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
(inclusions for XLR Insert Channels 3/4)
m (summary, formatting)
Line 1: Line 1:
 
<big>'''PS1 Connections Lines Out '''</big>  
 
<big>'''PS1 Connections Lines Out '''</big>  
 
+
== Summary ==
== XLR Line Outs Channels 1 and 2 ==
+
=== XLR Line Outs Channels 1 and 2 ===
 
* post trim (+4 dBu nominal)
 
* post trim (+4 dBu nominal)
  
== Insert Send ==
+
=== Insert Send ===
 
* post trim,
 
* post trim,
 
* post channel volume
 
* post channel volume
  
== SPDIF Data OUT ==
+
=== SPDIF Data OUT ===
 
* post trim,
 
* post trim,
 
* post channel volume and
 
* post channel volume and
Line 16: Line 16:
  
 
The Data OUT is a SPDIF output with a sampling rate of 48KHz
 
The Data OUT is a SPDIF output with a sampling rate of 48KHz
 
  
 
{{:PS1 Powerstand Connections/Line Out/XLR}}
 
{{:PS1 Powerstand Connections/Line Out/XLR}}
 
 
{{:PS1 Powerstand Connections/Line Out/Insert}}
 
{{:PS1 Powerstand Connections/Line Out/Insert}}
 
 
{{:PS1 Powerstand Connections/Line Out/Channel 3/4}}
 
{{:PS1 Powerstand Connections/Line Out/Channel 3/4}}
  

Revision as of 15:28, 14 November 2006

PS1 Connections Lines Out

Summary

XLR Line Outs Channels 1 and 2

  • post trim (+4 dBu nominal)

Insert Send

  • post trim,
  • post channel volume

SPDIF Data OUT

  • post trim,
  • post channel volume and
  • post insert returns.
  • It's PRE preset, tone controls & master volume.
  • SPDIF is channels 1 & 2 only.

The Data OUT is a SPDIF output with a sampling rate of 48KHz

Line Outs (XLR balanced) for Channels 1 and 2

  • post trim (+4 dBu nominal)

For Channels One or Two you can run an XLR cable to the House or recording console like this. The outputs are post-trim (+4 dBu nominal).

PS1LineOutXLR.jpg

This is not suitable for connection to another PS1 Power Stand (Classic) / Model I as the output level is too high for a PS1 Power Stand (Classic) / Model I Channel 1 or 2 input. If you want to connect one L1® to another please see: PS1 Powerstand / Daisy Chain


L1 Model I This information is applicable to the L1 Model I
Classic This information is applicable to the L1® Classic

Line Out from Insert Point

  • access from the "ring" connection at the Insert Point
  • post trim
  • post R1 Remote Channel Level

For Channels One or Two insert a 1/4 inch cable halfway into the Insert jack to get a signal that is controlled by the volume control on the Remote. This is also known as the Half Insert method. For more information about 1/4 cables see Tip Ring Sleeve connections. The rectangular box shown below the input panel is a DI, used to output the signal to a console or house system.

PS1LineOutInsert.jpg



Line Out from Channels 3 or 4

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I

There is no output from the PS1 Power Stand (Classic) / Model I for Channels 3 or 4. To share inputs with an external system use a DI.

PS1LineOutDI.jpg