S1 Pro Daisy Chain

From Bose Portable PA Encyclopedia
Revision as of 22:10, 3 April 2021 by ST (talk | contribs) (Created page with "{{S1 Pro Daisy Chain}}")
(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search

This is an overview of how to connect one S1 Pro System to another.

  1. On the first S1 Pro turn off the volumes of all channels
  2. Run the LINE OUT to the second S1 Pro system using a balanced cable (1/4 inch (6.3 mm) Tip-Ring-Sleeve cable
  3. On the second S1 Pro set the volume to 10:00 o'clock. This should give you the same volume on the second unit as the first
  4. On the first S1 Pro bring up the volume to the appropriate level on the channels you are using

S1 Pro Daisy Chain.jpg

There is no reason to turn the second S1 Pro system above 10:00 o'clock because it will be louder than the first system and the signal will clip and distort before the first system does.


On the second S1 Pro System, for each channel you are connecting to the first S1 Pro System use these settings while you are setting up.

S1 Pro Settings for mixer.jpg

  • Reverb OFF
  • Bass at 12:00 o'clock
  • Treble at 12:00 o'clock
  • ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System
Control the overall volume from the ToneMatch Mixer[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

ToneMatch Mixer to S1 Pro.jpg


Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

  1. Turn the channel volume off
  2. Connect your sound source
  3. Adjust the volume of the source device output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[2][3]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[4].
    • Refer to the manual for the source device for details.
    • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
  4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
  • XLR (balanced mono)
    • Microphone or Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
    • Line-Level inputs
  • 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
    • Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
  • The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
  • The S1 Pro XLR inputs are best suited for microphones.

When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.



Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer