Search results

Create the page "Insert" on this wiki! See also the search results found.

Page title matches

• Half Insert
  ...an half-insert a normal 1/4" plug into the {{PS1}} insert jack (that means insert to the first “click” but not all the way) and connect that to the input
  457 bytes (81 words) - 18:48, 6 November 2006
• Insert Cable
  <!-- to be used as an inclusion when mentioning insert cables --> Typical Insert Cable [http://www.sweetwater.com/store/detail/STP204/ Hosa STP204]
  198 bytes (31 words) - 12:20, 18 December 2006
• PS1 Powerstand Connections/Line Out/Insert
  == Line Out from Insert Point == * access from the "ring" connection at the Insert Point
  749 bytes (116 words) - 03:07, 29 April 2007
• T1 ToneMatch® Audio Engine / Insert for External Effects
  3 KB (477 words) - 04:48, 26 March 2017
• T1 ToneMatch® Audio Engine / Insert for Effects
  #REDIRECT [[T1 ToneMatch® Audio Engine / Insert for External Effects]]
  71 bytes (9 words) - 14:35, 26 February 2009
• T1 ToneMatch® Audio Engine / Insert for External Effects
  #REDIRECT [[T1 ToneMatch® Audio Engine / Insert for External Effects]]
  71 bytes (9 words) - 04:48, 26 March 2017

Page text matches

• Effects for the PS1 Powerstand
  [[Image:PS1InsertPoints.png|550px|right|Powerstand Insert Point]] ...y simply use the insert jack on the {{PS1}} . You probably will need an “insert” cable that has one [[TRS]] (stereo) 1/4” connector on one side and 2 m
  4 KB (675 words) - 11:34, 8 July 2010
• L1® Model I / FAQ
  ...into channels 1 or 2 of the power stand. These connectors require standard insert cables with 1/4" TRS connections on one end and dual male 1/4" TS connector === How do I know which half of the Cylindrical Radiator® to insert into the power stand first? ===
  60 KB (9,859 words) - 05:33, 26 March 2017
• R1 Remote
  ...signal has been reached at a point '''after the preamp''' and '''after the insert loop''' and '''before the conversion of the signal from analog to digital'' === LEDs and the Insert Loop ===
  11 KB (1,902 words) - 15:41, 23 April 2017
• PS1 Powerstand/Effects/Serial
  === Insert Cable === {{:Insert Cable}}
  698 bytes (95 words) - 11:32, 8 July 2010
• PS1 Powerstand Connections/Line Out/Insert
  == Line Out from Insert Point == * access from the "ring" connection at the Insert Point
  749 bytes (116 words) - 03:07, 29 April 2007
• PS1 Powerstand Connections / Line Out
  === Insert Send === **Insert returns
  1 KB (150 words) - 10:39, 5 November 2010
• Boss RC-30 Loop Station
  The INSERT point works really well with my Boss RC-30 Loop Station. I used a regular insert cable with the connections this way:
  1 KB (242 words) - 01:09, 28 March 2017
• Effects PS1 Powerstand TRS Connections
  ...sert Cables are labelled. '''This''' is how the connections are run at the Insert Point of the PS1 Powerstand. and this is connected to '''one''' of the PS1 Powerstand Insert Points
  448 bytes (66 words) - 00:39, 4 January 2007
• Effect / Alesis / MidiVerb4
  You will need one Insert Cable {{:Insert Cable}}
  935 bytes (127 words) - 18:34, 23 June 2009
• TC Electronic G-Force
  ...PARAMETER WHEEL to select the position where you wish to insert an effect and select which block to insert using the VALUE wheel. Route in serial or parallel,
  30 KB (3,215 words) - 13:19, 12 November 2008
• Half Insert
  ...an half-insert a normal 1/4" plug into the {{PS1}} insert jack (that means insert to the first “click” but not all the way) and connect that to the input
  457 bytes (81 words) - 18:48, 6 November 2006
• Insert Cable
  <!-- to be used as an inclusion when mentioning insert cables --> Typical Insert Cable [http://www.sweetwater.com/store/detail/STP204/ Hosa STP204]
  198 bytes (31 words) - 12:20, 18 December 2006
• L1® Model II / FAQ
  === How do I know which half of the Cylindrical Radiator® to insert into the power stand first? ===
  42 KB (6,832 words) - 05:25, 26 March 2017
• Balanced vs Unbalanced
  ...1/4 inch (6.3 mm) Tip-Ring-Sleeve to XLR]][[File:14 insert.jpg|thumb|100px|Insert cable]] * Insert (send and return)
  8 KB (1,267 words) - 17:43, 7 February 2023
• L1 Cylindrical Radiator® loudspeaker
  * Be careful how you insert the lower section. If you insert it upside down you may damage the connector in the Power Stand.
  12 KB (2,008 words) - 06:55, 26 March 2017
• Pad
  An inline pad can be easily soldered, you'll need to insert 3 resistors into your mic cable. The values of these three resistors are de To build a -20dB attenuation pad insert the following three resistors into your XLR cable path.
  5 KB (853 words) - 17:26, 14 May 2017
• Troubleshooting
  ...c}} or {{Model I}} remove anything connected to the Channel 1 or Channel 2 insert points. ** Make sure input sources are NOT plugged into Channel 1 or Channel 2 '''Insert''' points
  7 KB (1,133 words) - 16:32, 13 October 2010
• Presets 2 Upgrade instructions
  # Insert the CD #1 DSP Software Update 1.84 disc into the DVD player. Press the STOP # Insert the CD #2 Presets 2.0 Update disc into the DVD player. Press the STOP butto
  7 KB (1,127 words) - 15:32, 1 November 2016
• PS1 Powerstand/ Preventing Incorrect Connections
  ...ng setup (such as putting a 1/4 intended for channel 4 into the channel 2 "Insert" socket, or plugging the B1 cable into Amp 2 output) - particularly during ...e door wouldn't close (the closed door comes really close to the channel 2 insert socket).
  2 KB (377 words) - 23:26, 15 August 2007
• Peavey Kosmos® Pro
  Setup: Used the Insert connector on the PS1 to route through the main in/out in the Kosmos Pro. ...udio directly into the PS1s, channel 1, using 00 preset. Use the channel's INSERT connector to connect to the Kosmos' main I/O. Don't use the Kosmos' subwoof
  6 KB (957 words) - 18:38, 26 March 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)