Difference between revisions of "T1® to Denon DN-X500"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m ({{T1}} to Denon DN-X500 Effects Return)
m ({{T1}} to Denon DN-X500 microphone input)
Line 13: Line 13:
  
 
[[Image:DN-X500Input4T1.png]]
 
[[Image:DN-X500Input4T1.png]]
 +
 +
==== Notes that apply to all three approaches ====
 +
You'll need a [[T1_ToneMatch%C2%AE_Audio_Engine_power_supply|T1 ToneMatch%C2%AE Audio Engine power supply]][IMG]http://toonz.ca/bose/wiki/images/d/d8/T1_power_supplyThumb.jpg[/IMG]     
 +
 +
The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control to get a good level match to the input that you use on the Denon-DNX500.
 +
 +
Make the connection with a ¼ inch jack Tip-Ring-Sleeve cable.
 +
 +
[[Image:TrsMtrsM.png]] 
 +
  
 
==== {{T1}} to Denon DN-X500 microphone input ====
 
==== {{T1}} to Denon DN-X500 microphone input ====
The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control.
+
 
 +
 
 +
 
 +
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
  
 
The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.  
 
The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.  
  
 
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
 
Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.
 +
 +
This is a screen shot of English page 3 with an overlay of the back of the T1® ΞΘ∞∋--
 +
  
 
[[Image:DN-X500Input4T1-Aux.png]]
 
[[Image:DN-X500Input4T1-Aux.png]]
 +
 
==== {{T1}} to Denon DN-X500 Effects Return ====
 
==== {{T1}} to Denon DN-X500 Effects Return ====
 
This could give you a better match for levels and impedance, but you will have to control everything with the T1®. Start with the master output of the T1® all the way off and bring it up slowly.  
 
This could give you a better match for levels and impedance, but you will have to control everything with the T1®. Start with the master output of the T1® all the way off and bring it up slowly.  

Revision as of 03:39, 17 May 2014

T1® to Denon DN-X500

Connection an T1 ToneMatch Audio Engine to a Denon DN-X500

There are three connections on the Denon DN-X500 where you could connect a T1 ToneMatch Audio Engine Master or Aux output.

T1 ToneMatch Audio Engine to Denon DN-X500 microphone input

The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control.

The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.

Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.

DN-X500Input4T1.png

Notes that apply to all three approaches

You'll need a T1 ToneMatch%C2%AE Audio Engine power supply[IMG]T1_power_supplyThumb.jpg[/IMG]

The T1® Master Output is a line level output. You can raise and lower that with the Master Volume control to get a good level match to the input that you use on the Denon-DNX500.

Make the connection with a ¼ inch jack Tip-Ring-Sleeve cable.

TrsMtrsM.png


T1 ToneMatch Audio Engine to Denon DN-X500 microphone input

Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.

The Denon DN-X500 has level controls for both the Main Mic and Aux Mic inputs.

Start with the master output of the T1® all the way off and bring it up slowly. You will also want to have the DN-X500 microphone input level set quite low to start until you figure out the levels so that you don't have any clipping.

This is a screen shot of English page 3 with an overlay of the back of the T1® ΞΘ∞∋--


DN-X500Input4T1-Aux.png

T1 ToneMatch Audio Engine to Denon DN-X500 Effects Return

This could give you a better match for levels and impedance, but you will have to control everything with the T1®. Start with the master output of the T1® all the way off and bring it up slowly.

DN-X500Input4T1-EffectsReturn.png

Reference Notes: Denon DN-X500 User Manual

http://usa.d-mpro.com/DocumentMaster/US/f1160bc969bf42e0bc5e90b6600c5207.pdf