Difference between revisions of "T1 ToneMatch® Audio Engine / Microphone into Channel 4"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
(first edit)
 
m
 
(10 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
{{T1 icon}}
 
{{T1 icon}}
  
[[Image:T1Channel45Input.png]]
+
You can use four microphones with a {{T1}} even though there are only 3 XLR inputs. Channel 4/5 can be used if you have an impedance matching transformer. Note that if your microphone requires phantom power, then you will need to supply that too as there is no phantom power on {{T1 nl}} Channel 4/5.
 +
 
 +
[[Image:T1Channel45Input.png]]        [[Image:Lo to Hi Impedance Matching Transformer.jpg|50px|Impedance Matching Transformer]] or [[Image:LoToHighImpedanceMatchingTransformer.jpg]]
 +
 
 +
==== Dynamic Microphone  ====
 +
Microphone ⇒ microphone cable ⇒ Lo-to-High impedance matching transformer.
 +
 
 +
[[Image:T1Channel4Microphone01.jpg]]
  
You can use four microphones with a {{T1}} even though there are only 3 XLR inputs. Channel 4/5 can be used if you have an impedance matching transformer. Note that if your microphone requires phantom power, then you will need to supply that too as there is no phantom power on {{T1 nl}} Channel 4/5.
+
I used the microphone above and set the trim for T1® Channel 3 and then I use the same microphone with the impedance matching transformer in T1® Channel 4/5.  The picture below shows that I was able to get the same input level on Channels 3 and 4 by using a higher trim setting on Channel 4/5. Please note: Your settings will probably be different depending on your microphone and your vocal style. The picture is to show you that the trim setting for Channel 4/5 will probably be higher than Channel 3. This does not affect the sound quality.
 +
 
 +
[[Image:T1Channel4Microphone003.jpg]]
 +
 
 +
===== Different Adapter / Same Results =====
 +
Note: This adapter also has an impedance matching transformer built into it.
 +
 
 +
[[Image:T1Channel4Microphone002.jpg]]
  
[[Image:Lo to Hi Impedance Matching Transformer.jpg|20px|right|Impedance Matching Transformer]]
+
==== Condenser Microphone ====
 +
The microphone shown here is a clip-on instrument microphone, but if you are using a vocal microphone the same connections would apply.
  
 +
Note: the Isomax device shown below is a standalone phantom power supply. You will not need this unless your microphone requires phantom power.
  
 
[[Image:T1 Channel 4 Impedance Match Phantom.jpg]]
 
[[Image:T1 Channel 4 Impedance Match Phantom.jpg]]
Line 13: Line 29:
 
* Phantom power supply
 
* Phantom power supply
 
* xlr cable
 
* xlr cable
* Lo to Hi Impedance matching transformer
+
* Lo to Hi Impedance matching transformer
 +
** [sweetwater.com/store/detail/LittleIMP--whirlwind-little-imp-lo-z-xlr-to-hi-z-1-4-inch-inline-impedance-matcher Whirlwind Little IMP Lo-Z XLR to Hi-Z 1/4" Inline Impedance Matcher]
 +
** [https://www.audiopile.net/CA-321 CA-321 | 3 PIN FXLR TO M1/4" TS TRANSFORMER BARREL ADAPTOR]
 +
** [http://www.long-mcquade.com/?page=products&ProductsID=5309  LoZ to HiZ Transformer Cable - 6 foot]
  
 
Note: the phantom power supply is only required if your microphone requires phantom power (e.g. condenser microphone). Most dynamic microphones will not require you to use a phantom power supply.  
 
Note: the phantom power supply is only required if your microphone requires phantom power (e.g. condenser microphone). Most dynamic microphones will not require you to use a phantom power supply.  
  
 +
 +
Field Report:
 +
<blockquote>
 +
I just tried this out.
 +
 +
Small diaphragm condenser microphone
 +
 +
to
 +
 +
external phantom power supply
 +
 +
to
 +
 +
a low to high impedance matching transformer for the microphone
 +
(click the picture for details)
 +
 +
 +
to
 +
 +
T1® Channel 4/5
 +
 +
I had to turn the input trim higher on Channel 4/5 than when I plugged the microphone directly into Channel 1,2,3 - but it worked.
 +
 +
NOTE - you have to have the impedance matching transformer.
 +
 +
</blockquote>
 +
 +
&mdash; Source:  [http://bose.infopop.cc/eve/forums/a/tpc/f/301107819/m/7130026336?r=4800068536#4800068536 String Quartet - Bun]
 
----
 
----
 
[[Category:T1]]
 
[[Category:T1]]
 
[[Category:Connections]]
 
[[Category:Connections]]
 
[[Category:Adapters]]
 
[[Category:Adapters]]

Latest revision as of 17:25, 9 December 2022

T1 This information is applicable to the T1 ToneMatch® audio engine

You can use four microphones with a T1 ToneMatch Audio Engine even though there are only 3 XLR inputs. Channel 4/5 can be used if you have an impedance matching transformer. Note that if your microphone requires phantom power, then you will need to supply that too as there is no phantom power on T1 ToneMatch® Audio Engine Channel 4/5.

T1Channel45Input.png        Impedance Matching Transformer or LoToHighImpedanceMatchingTransformer.jpg

Dynamic Microphone

Microphone ⇒ microphone cable ⇒ Lo-to-High impedance matching transformer.

T1Channel4Microphone01.jpg

I used the microphone above and set the trim for T1® Channel 3 and then I use the same microphone with the impedance matching transformer in T1® Channel 4/5. The picture below shows that I was able to get the same input level on Channels 3 and 4 by using a higher trim setting on Channel 4/5. Please note: Your settings will probably be different depending on your microphone and your vocal style. The picture is to show you that the trim setting for Channel 4/5 will probably be higher than Channel 3. This does not affect the sound quality.

T1Channel4Microphone003.jpg

Different Adapter / Same Results

Note: This adapter also has an impedance matching transformer built into it.

T1Channel4Microphone002.jpg

Condenser Microphone

The microphone shown here is a clip-on instrument microphone, but if you are using a vocal microphone the same connections would apply.

Note: the Isomax device shown below is a standalone phantom power supply. You will not need this unless your microphone requires phantom power.

T1 Channel 4 Impedance Match Phantom.jpg

Note: the phantom power supply is only required if your microphone requires phantom power (e.g. condenser microphone). Most dynamic microphones will not require you to use a phantom power supply.


Field Report:

I just tried this out.

Small diaphragm condenser microphone

to

external phantom power supply

to

a low to high impedance matching transformer for the microphone (click the picture for details)


to

T1® Channel 4/5

I had to turn the input trim higher on Channel 4/5 than when I plugged the microphone directly into Channel 1,2,3 - but it worked.

NOTE - you have to have the impedance matching transformer.

— Source: String Quartet - Bun