T1 ToneMatch® Audio Engine / 1/4 inch Output Connections to L1® Family Members

From Bose Portable PA Encyclopedia
(Redirected from Template:1/4 inch from T1)
Jump to: navigation, search

Connecting from a T1 ToneMatch Audio Engine ¼ inch jack (Master or Aux) to other members of the L1® Family is simple. This article is applicable to L1 Compact, L1 Classic, L1 Model I, L1 Model II S1 Pro System.

T1MasterOrAuxAnalog.png

T1 Master Output T1 Aux Output T1 Preamp Outs for Channels 1,2,3

Overview

You can use TS (Tip-Sleeve) unbalanced cables, OR TRS (Tip-Ring-Sleeve) balanced cables. If the cable uses ¼ inch jack plugs and the ends are the same, then the cable should be fine.

Tip-Sleeve to Tip-Sleeve

OR

Tip-Ring-Sleeve to Tip-Ring-Sleeve


Classic or Model I

For full details see: T1 ToneMatch® Audio Engine / Power Stand Input Setting

¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

This should work fine.

Tip-Sleeve to Tip-Sleeve


¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

Since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables but there is no harm.

Tip-Ring-Sleeve to Tip-Ring-Sleeve

L1 Model II


¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.

Tip-Ring-Sleeve to Tip-Ring-Sleeve

¼ Inch Tip-Ring-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

This should work fine but a balanced connection (immediately above) is preferred especially if you will have cable runs in excess of 20 feet (6 meters) or if you hear line noise, hum or hiss.

Tip-Sleeve to Tip-Sleeve



L1 Compact


You can connect a T1 ToneMatch Audio Engine to L1 Compact


Here is an excerpt from page 12 of the L1® Compact Owner's Guide (pdf format)

CompactOwnersGuideT1Connection.gif

Connect FROM T1 ToneMatch Audio Engine Master or Aux Output using ¼ inch jack connections.

Connect TO the Compact Channel 2 volume straight up (12:00 o'clock to 1:00 o'clock) for good results. You can turn it up higher, but if you see the light on the Compact solid red (flickers of red are okay) or you hear distortion, turn down the volume on the Compact.


¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.

Tip-Ring-Sleeve to Tip-Ring-Sleeve

¼ Inch Tip-Ring-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

This should work fine but a balanced connection (immediately above) is preferred especially if you will have cable runs in excess of 20 feet (6 meters) or if you hear line noise, hum or hiss.

Tip-Sleeve to Tip-Sleeve



Channel 2 Connection from T1 ToneMatch Audio Engine Details

Connect the T1 ToneMatch Audio Engine Master output L1 Compact channel 2.

T1MasterOutput.png

Compact Channel 2 Line Level.png

Turn the Channel 1 volume all the way down (fully counterclockwise) unless you have a microphone attached to it.


Two T1®s to a Single Compact

Two T1®s to Separate Inputs on Compact Channel 2

T1x2IntoCompact01.png

Compact Channel 2 detail

Compact Channel 2 Line Level and RCA.png

Suggested by Tom the Guitar Guy[1]

Daisy Chain Two T1®s to Compact Channel 2

T1x2IntoCompact02.png


Compact Channel 2 detail

Compact Channel 2 Line Level.png


  1. Tom the Guitar Guy in the Bose L1® Forum



F1 Model 812 Flexible Array Loudspeaker

Please see: T1 ToneMatch® Audio Engine to F1 System

T1 to F1
Click the picture to read the full article

S1 Pro System

On the S1 Pro System, for each channel you are connecting to the mixer use these settings while you are setting up.

S1 Pro Settings for mixer.jpg

  • Reverb OFF
  • Bass at 12:00 o'clock
  • Treble at 12:00 o'clock
  • ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System
Control the overall volume from the ToneMatch Mixer[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

ToneMatch Mixer to S1 Pro.jpg


Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

  1. Turn the channel volume off
  2. Connect your sound source
  3. Adjust the volume of the source device output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[2][3]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[4].
    • Refer to the manual for the source device for details.
    • If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
  4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.



¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.

Tip-Ring-Sleeve to Tip-Ring-Sleeve

¼ Inch Tip-Ring-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

This should work fine but a balanced connection (immediately above) is preferred especially if you will have cable runs in excess of 20 feet (6 meters) or if you hear line noise, hum or hiss.

Tip-Sleeve to Tip-Sleeve