Difference between revisions of "Template:T1 ToneMatch® Audio Engine power supply"
m |
m (expanded use cases for power supply) |
||
| Line 1: | Line 1: | ||
This is the power supply for the {{T1}}. You will need this to power your {{T1 nl}} when running with an {{Classic}}, {{Model I}}. | This is the power supply for the {{T1}}. You will need this to power your {{T1 nl}} when running with an {{Classic}}, {{Model I}}. | ||
| − | If you connect your {{T1 nl}} to a {{Model II}} then the {{T1 nl}} draws its power through the ToneMatch® cable. <br> | + | If you connect your {{T1 nl}} to a {{Model II}} then the {{T1 nl}} draws its power through the ToneMatch® cable. If you are attaching two {{T1 nl}}s to a single {{Model II nl}} then you will need this power supply to support the second T1®. <br />See: {{:T1 ToneMatch® Audio Engine / Connections to Model II|Connecting Two T1®s to a Model II}} for details.<br> |
{{#Click:http://www.bose.com/controller?url=/shop_online/speakers/portable_amplification_systems/accessories/l1_tonematch_powersupply_acc.jsp|Image:L1 tonematch powersupply acc bl lg.jpg|100|T1 ToneMatch® Audio Engine power supply}} | {{#Click:http://www.bose.com/controller?url=/shop_online/speakers/portable_amplification_systems/accessories/l1_tonematch_powersupply_acc.jsp|Image:L1 tonematch powersupply acc bl lg.jpg|100|T1 ToneMatch® Audio Engine power supply}} | ||
Revision as of 11:43, 5 December 2008
This is the power supply for the T1 ToneMatch Audio Engine. You will need this to power your T1 ToneMatch® Audio Engine when running with an L1 Classic, L1 Model I.
If you connect your T1 ToneMatch® Audio Engine to a L1 Model II then the T1 ToneMatch® Audio Engine draws its power through the ToneMatch® cable. If you are attaching two T1 ToneMatch® Audio Engines to a single L1® Model II then you will need this power supply to support the second T1®.
See:
The L1 Model II can accept two inputs.
This makes it easy for two performers to connect their own T1®s to a L1® Model II Power Stand.
Contents
ToneMatch® Input
The ToneMatch® connection is specifically designed for a T1 ToneMatch Audio Engine. The ToneMatch® cable is supplied with the T1 ToneMatch Audio Engine and uses a male Ethercon connector at both ends.
Analog Input
The Analog connection is a ¼ inch phone jack. You can use this for a second T1® using the T1® Analog Master output (¼ inch phone jack).
This connection is made with a standard ¼ inch jack instrument cable. This can be Tip-Sleeve or Tip-Ring-Sleeve connectors.
Set Power Stand Analog Input Trim to 3 to have approximately the same level as you would have if you had connected with the ToneMatch® connection. You may have to adjust this, but 3 is a good place to start.
Note: A T1® connected to the the Analog input will require the optional T1 ToneMatch® Audio Engine power supply.
Analog Connection from the Second T1® to the Model II Power Stand
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
A balanced connection is preferred and will provide better noise rejection over greater distances than the unbalanced connection.
¼ Inch Tip-Ring-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine but a balanced connection (immediately above) is preferred especially if you will have cable runs in excess of 20 feet (6 meters) or if you hear line noise, hum or hiss.
for details.
{{#Click:http://www.bose.com/controller?url=/shop_online/speakers/portable_amplification_systems/accessories/l1_tonematch_powersupply_acc.jsp%7CImage:L1 tonematch powersupply acc bl lg.jpg|100|T1 ToneMatch® Audio Engine power supply}}
Click image above for purchasing details