Difference between revisions of "Template:T1 to Model I or Classic"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
(First edition of this template (material appeared in article before))
 
m (added the documentation about the change to documentation (use 3 for input level))
Line 50: Line 50:
  
 
[[Image:T12ModelI.png]]
 
[[Image:T12ModelI.png]]
 +
 +
With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.
 +
 +
The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.
 +
 +
=== Input setting recommendation now '''3'''  ===
 +
<section begin=InputSettingNow3 />
 +
MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this.
 +
 +
For these conditions:
 +
{{Classic icon}}{{Model I icon}}
 +
* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4
 +
* Balanced OR Unbalanced 1/4" cable
 +
* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock
 +
* Proper gain staging required on the T1® itself
 +
 +
I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions.
 +
 +
This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}.
 +
 +
If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.
 +
<section end=InputSettingNow3 />
 +
 +
Hopefully this is helpful - please ask away with any questions for clarification.
 +
 +
MikeZ

Revision as of 22:51, 14 January 2009

This Page Reviewed By Bose

Here are details on how to connect a T1 ToneMatch Audio Engine to a L1 Classic or L1 Model I

T1toPS1.png

Notes:


T1 This information is applicable to the T1 ToneMatch® audio engine
L1 Model I This information is applicable to the L1 Model I
Classic This information is applicable to the L1® Classic

The recommended trim setting input Ch 3 or Ch 4 is 3 (see below).

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote. More on this later.

For these conditions:

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I

  • T1 ToneMatch® Audio Engine going into L1® Model I/L1® Classic into Channel 3/4
  • Balanced OR Unbalanced 1/4" cable
  • Remote unplugged, OR, master volume on Remote at 12 o clock
  • Proper gain staging required on the T1® itself

This will give you the same gain going into the L1® Model I/L1® Classic as if you were going through the ToneMatch® input on a L1 Model II.

If you are using the Remote on your L1® Model I/L1® Classic, then you will need to compensate a bit. If you are running the Remote master volume at max, then stick with 2 on Ch 3/4. When using a T1®, run the master volume of the R1 above 12 o'clock .


Connection to L1 Model I / L1 Classic with Remote

If you want to use the PS1 Power Stand Channels 1 or 2 or 4, then you will want to connect the R1 Remote to the PS1 Power Stand.

T1toPS1withRemote.png



Excerpt from the T1 ToneMatch Audio Engine Manual - page 20 - Note: this recommended input setting is now 3. See the note above.

T12ModelI.png

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote.

The T1 ToneMatch Audio Engine controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.

Input setting recommendation now 3

MikeZ-at-Bose wrote[1] Bill-at-Bose and I have revisited this.

For these conditions:

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I

  • T1 ToneMatch® Audio Engine going into L1® Model I/L1® Classic into Channel 3/4
  • Balanced OR Unbalanced 1/4" cable
  • Remote unplugged, OR, master volume on Remote at 12 o clock
  • Proper gain staging required on the T1® itself

I'm going to revise the original recommendation of 2 for Ch 3/4 to 3 - under the above conditions.

This will give you the same gain going into the L1® Model I/L1® Classic as if you were going through the ToneMatch® input on a L1 Model II.

If you are using the Remote on your L1® Model I/L1® Classic, then you will need to compensate a bit. If you running the Remote master volume at max, then stick with 2 on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®.


Hopefully this is helpful - please ask away with any questions for clarification.

MikeZ