Difference between revisions of "Template:ToneMatch Power Supply"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m
m
 
Line 1: Line 1:
ToneMatch® Audio Engine power supply. This is the power supply for the {{ToneMatch Mixer}}. You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or  or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}.  —  details below the picture.  
+
ToneMatch® Audio Engine power supply.  
 +
 
 +
This is the power supply for the {{ToneMatch Mixer}}.  
 +
 
 +
==== Not Required with {{L1P}} ====
 +
The {{L1P}} systems have a ToneMatch port that can supply power to any ToneMatch mixer.
 +
 
 +
 
 +
==== Required with Earlier Systems except {{Model II}} ====
 +
 
 +
You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}.  —  details below the picture.  
  
 
[[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]]  
 
[[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]]  

Latest revision as of 18:46, 6 December 2020

ToneMatch® Audio Engine power supply.

This is the power supply for the ToneMatch Mixer[1].

Not Required with L1 Pro[2]

The L1 Pro[2] systems have a ToneMatch port that can supply power to any ToneMatch mixer.


Required with Earlier Systems except L1 Model II

You will need this to power your ToneMatch Mixer[1] when running with an L1 Compact, S1 Pro System, L1 Classic, L1 Model I, or non-Bose equipment. You will need a one of these if you have two ToneMatch Mixer[1]s running into a single L1® Model II or L1® Model 1S. — details below the picture.

T1 ToneMatch® Audio Engine power supply

Click image above for purchasing details.


If you connect your T1 ToneMatch® Audio Engine to a L1 Model II or L1 Model 1S then the T1 ToneMatch® Audio Engine draws its power through the ToneMatch® cable.

If you connect your T1 ToneMatch® Audio Engine to an an L1 Classic, L1 Model I or L1 Compact or non-Bose equipment then you will need the T1 ToneMatch® Audio Engine power supply


If you are attaching two T1 ToneMatch® Audio Engines to a single L1® Model II then you will need this power supply to support the second T1® - the one connected to the Power Stand Analog Input.

See: Connecting Two T1®s to a Model II for details.



If you disassemble the Ethercon connector (not recommended), it's tricky to reassemble it.

NE8MX-B-1.jpg


Note: There are small guides on the grey piece that slide into the slots in the barrel.

NE8MX-B-12.jpg


Media:BDA 564 - etherCON NE8MX-1 & NE8MX-B-1 - RJ45 cable connector carrier.pdf


Close up of the connector that goes to the ToneMatch Mixer[1], just in case you damage the cable and have to replace the connector.

Note: The picture is taken with the flat side facing the camera. The release clip is on the other side.

Close up of the RJ45 connector



  1. 1.0 1.1 1.2 1.3 T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine
  2. 2.0 2.1 L1 Pro 8, L1 Pro 16, L1 Pro 32