View source for Template:T1 to Model I or Classic

<noinclude>{{Bose Reviewed}}</noinclude>
=== Connection to {{Model I}} / {{Classic}} with NO Remote ===
Here are details on how to connect a {{T1}} to a {{Classic}} or {{Model I}}

[[Image:T1toPS1.png]]

Notes: 

<section begin=InputSettingNow3 />
{{T1 icon}}{{Model I icon}}{{Classic icon}} The recommended setting for Channel 3 or Channel 4 Level is '''3''' (see below). 

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote. More on this later.

For these conditions: 
{{Classic icon}}{{Model I icon}}
* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4 
* Balanced OR Unbalanced 1/4" cable 
* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock 
* Proper gain staging required on the T1® itself

This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}. 

If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you are running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. When using a T1®, run the master volume of the R1 above 12 o'clock . 
<section end=InputSettingNow3 />


=== Connection to {{Model I}} / {{Classic}} with Remote ===
If you are using Channel 3 for the {{t1 nl}} AND you want to use the PS1 Power Stand Channels 1 or 2 or 4 for other inputs, then you will want to connect the R1 Remote to the PS1 Power Stand.

[[Image:T1toPS1withRemote.png]]


<!--
=== Connections to a Model I or Classic ===
MikeZ-at-Bose gave us some more insight<ref>MikeZ-at-Bose talking about [http://bose.infopop.cc/eve/forums/a/tpc/f/3976055944/m/100102183?r=5671030415#5671030415 T1&trade; to Model I Connections]</ref>

Without getting too deep into technical stuff, with regards to the {{t1 nl}} the two ways to interface with a {{Model I}} are:

1.) The way we generally recommend - 1/4" out from the {{t1 nl}} into Ch 3/4 with the Level at '''3'''.

2.) 1/4" balanced {{TRS}} from the T1 to XLR input of Ch 1/2. Of course this requires a TRS to XLR cable which most folks don't have lying around - but is a common studio connector available at GC etc.

Both ways are equal as long as your distance from the {{Model I}} or {{Classic}} is less than 25 or 30 feet. Longer than that I would lean toward option #2.Method #1 allows you not to use a preset Channel on the model I.

--> 

----

Excerpt from the {{T1}} Manual - page 20 - Note: this recommended input setting is now '''3'''. See the note above. 

[[Image:T12ModelI.png]]

With this setting you will not distort or clip the Model 1 no matter what you do on the T1. You can even use the Model 1 without the remote. 

The {{T1}} controls are a heck of a lot faster then the R1 controls. There is no perceivable lag.

=== Input setting recommendation now '''3'''  ===
<section begin=InputSettingNow3 />
MikeZ-at-Bose wrote<ref>MikeZ-at-Bose talks about [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/3041050644?r=7271069184#7271069184 the input setting on the {{Model I nl}} or {{Classic nl}} Power Stand with the T1®] </ref> Bill-at-Bose and I have revisited this. 

For these conditions: 
{{Classic icon}}{{Model I icon}}
* {{T1 nl}} going into {{Model I nl}}/{{Classic nl}} into Channel 3/4 
* Balanced OR Unbalanced 1/4" cable 
* {{Remote}} unplugged, OR, master volume on {{Remote}} at 12 o clock 
* Proper gain staging required on the T1® itself

I'm going to revise the original recommendation of '''2''' for Ch 3/4 to '''3''' - under the above conditions. 

This will give you the same gain going into the {{Model I nl}}/{{Classic nl}} as if you were going through the [[ToneMatch® Cable|ToneMatch®]] input on a {{Model II}}. 

If you are using the {{Remote}} on your {{Model I nl}}/{{Classic nl}}, then you will need to compensate a bit. If you running the {{Remote}} master volume at max, then stick with '''2''' on Ch 3/4. I would recommend against running the master volume below 12 o'clock when using a T1®. 
<section end=InputSettingNow3 />

Hopefully this is helpful - please ask away with any questions for clarification. 

MikeZ


----
<references />