Search results

Create the page "Power" on this wiki! See also the search results found.

• Pad
  ...kely place you will use this is in front of a [[Model I]] (or [[Classic]]) Power Stand Channel 1 or Channel 2. ...hts up earlier than expected. You can put a 10 dB Pad between the Model II Power Stand Bass Line Out and the {{A1}} input.
  5 KB (853 words) - 17:26, 14 May 2017
• L1® Model II Documentation
  ...I weight. Both are listed as 35lbs. I made a mistake before by saying the power stand is a 'couple pounds' lighter. In reality it is less than a pound ligh ==== Classic / Model I Power Ratings ====
  4 KB (644 words) - 05:26, 26 March 2017
• Ground Loop
  NEVER use a cheater plug or cut the ground plug off an ac power cord. NEVER use a cheater plug or cut the ground plug off an ac power cord.
  8 KB (1,303 words) - 09:31, 7 April 2019
• Mixer to Share Presets
  * Take the pooled output (one side of the mixer) to Power Stand Channel 1 and use a Preset that is appropriate for the input. * Take the pooled output (the other side of the mixer) to Power Stand Channel 2 and use a Preset that is appropriate for the input, or Pres
  3 KB (463 words) - 15:12, 28 December 2012
• Laptop Hum
  ...speakers or headphones that occurs only when my system is connected to AC power?" ...the computer and any external speakers are plugged into the same outlet or power strip. This should eliminate or minimize the buzzing associated with a grou
  2 KB (314 words) - 09:37, 7 April 2019
• T1 ToneMatch® Audio Engine / Connections to Model II
  ...it easy for two performers to connect their own T1®s to a {{Model II nl}} Power Stand. Set Power Stand Analog Input Trim to '''3''' to have approximately the same level as
  1 KB (231 words) - 04:42, 26 March 2017
• Hammered Dulcimer
  '''Plugging a Hammered Dulcimer into the L1 Model I Power Stand''' * Furman power conditioner
  4 KB (633 words) - 15:56, 14 October 2008
• Fiddle
  ...up or mic clipped to their instrument, plugging direct into the L1 Model 1 power stand may pose special challenges. In spite of all, "bow scritch" and a ce * Furman power conditioner
  4 KB (691 words) - 15:30, 22 December 2008
• L1® Model I / FAQ Extension
  * Make sure the power switch on the power stand is in the Off position and the remote control is disconnected<br> ...ure the ToneMatch audio engine power switch is in the Off position and its power supply is connected
  2 KB (255 words) - 18:27, 26 March 2017
• Stereo / Mono / Distributed Systems
  === Bass Power Alley === ...create an audible "power alley"<ref>Related reading: [[Media:The-Subwoofer-Power-Alley-1.pdf]]</ref>. Once you get beyond these distances, the balloon anima
  8 KB (1,432 words) - 15:37, 23 September 2023
• Is the B2 Bass Module Compatible with the L1® Classic or Model I
  ...It triggers switching at the Power Stand to which it is attached, if that Power Stand is a Model 1S or Model II with firmware version 1.4 or later. </td><tr><td valign="top">D</td><td> Four B1s <br />using an [[PackLite® power amplifier Model A1]]
  7 KB (1,259 words) - 08:44, 26 March 2017
• ToneMatch® Mixer to S1 Pro System
  === Power Supply === You will need at ToneMatch Power Supply to power the ToneMatch mixer unless you are using a T4S also connected to an L1 Mode
  740 bytes (132 words) - 22:24, 16 November 2019
• T8S to L1 Model II
  * Connect the ToneMatch Power Supply to the {{T8S}} for power. * Always use the ToneMatch Power Supply connected to the {{T8S}} ToneMatch port.
  1 KB (231 words) - 12:31, 10 April 2019
• Bose L1 Pro8 Compared to L1 Compact
  <td>One 7"x 13" neodymium racetrack transducer in the power stand ...8" (203 mm) low-frequency driver mounted in a ported bass enclosure in the power stand
  7 KB (1,045 words) - 15:04, 12 June 2021
• Do I Need to Upgrade from the L1 Compact to the L1 Pro8?
  ...icrophone is a Neumann KMS 105 (condenser microphone that requires phantom power). I have some dynamic microphones that work well with the L1 Compact, but I The L1 Pro8 is just as portable as the L1 Compact. The power stand is just six pounds heavier (31 pounds vs. 25). The extension and mid-
  5 KB (829 words) - 18:18, 30 November 2021
• Bose L1 Model II Compared to L1 Pro32
  <td>Power to speakers <li>Power Stand&nbsp;480 Watts RMS mid-high array</li>
  11 KB (979 words) - 16:27, 23 September 2023
• Sub1/Sub2
  * Fixes an issue that allows users to disable Low Power Standby mode. ...mparisons are approximate and this assumes that other variables like input power are similar:
  6 KB (935 words) - 20:29, 5 December 2023
• Bose L1 Model 1S Compared to L1 Pro16
  <td>One 10"x 18" racetrack transducer in the power stand <td>Power to speakers
  11 KB (856 words) - 21:13, 11 June 2021
• Gain Staging
  ...&ck=0#question32 What is the proper method for setting the gain on the PS1 Power Stand?]</ref> ...gain. Set the trim for the individual channel at the back panel of the PS1 Power Stand. Supply a maximum source signal and watch the LED, when you start to
  7 KB (1,267 words) - 00:54, 30 November 2016
• Gain Staging/Chuck-at-Bose
  * Power Amp – A last big boost, by far the biggest of all, so big that it can mak === Full Power at 12:00 on Master Level ===
  7 KB (1,190 words) - 17:51, 29 December 2007

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)