Difference between revisions of "Denon DN-MC6000"
m (New page: Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. See the diagram below (from [http://www.dm-pro.eu/DocumentMaster...) |
m |
||
| Line 1: | Line 1: | ||
Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. | Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. | ||
| − | See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10] | + | See the diagram below (from [http://www.dm-pro.eu/DocumentMaster/en/dnmc6000emcd-romengim001.pdf Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)] |
[[Image:Denon DN-MC6000 Output.png]] | [[Image:Denon DN-MC6000 Output.png]] | ||
| − | Running mono, set the output to MONO above and connect to the | + | Running mono, set the output to MONO above and connect to the [[L1%C2%AE_Model_II#Analog_Input Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input Model 1S Analog input]] |
| + | |||
| + | [[http://toonz.ca/bose/wiki/images/b/b6/Model_1S_Analog_Input_Detail.png]] | ||
| + | |||
| + | With a cable like this: | ||
[[Image:XLR to TRS mp106.jpg]] | [[Image:XLR to TRS mp106.jpg]] | ||
[http://www.audiopile.net/products/Mic_Instr_Cables/MP_Adaptor_Cbls/MP-105/MP-105_cutsheet.shtml Source: Audiopile.net] | [http://www.audiopile.net/products/Mic_Instr_Cables/MP_Adaptor_Cbls/MP-105/MP-105_cutsheet.shtml Source: Audiopile.net] | ||
| + | |||
| + | Technical Description: | ||
| + | |||
| + | The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment. | ||
| + | |||
| + | The Female XLR end is wired through to the 1/4" Male TRS end as follows: | ||
| + | |||
| + | * Pin One FXLR to Sleeve of MTRS | ||
| + | * Pin Two FXLR to Tip of MTRS | ||
| + | * Pin Three FXLR to Ring of MTRS | ||
| + | |||
| + | The 1/4" MTRS end is an EWI model P292S-BKG | ||
| + | |||
| + | The FXLR end is an EWI model ES3FB-GDP | ||
| + | |||
| + | The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | ||
Revision as of 03:40, 6 December 2013
Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact.
See the diagram below (from Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)
Running mono, set the output to MONO above and connect to the L1®_Model_II#Analog_Input Model II Analog input or L1®_Model_1S#Analog_Input Model 1S Analog input
[[1]]
![[1]](http://toonz.ca/bose/wiki/images/b/b6/Model_1S_Analog_Input_Detail.png){kind=link}
With a cable like this:
Technical Description:
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
The Female XLR end is wired through to the 1/4" Male TRS end as follows:
- Pin One FXLR to Sleeve of MTRS
- Pin Two FXLR to Tip of MTRS
- Pin Three FXLR to Ring of MTRS
The 1/4" MTRS end is an EWI model P292S-BKG
The FXLR end is an EWI model ES3FB-GDP
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.