Difference between revisions of "Denon DN-MC6000"
m |
m |
||
| Line 10: | Line 10: | ||
[[Image:Denon DN-MC6000 Output.png]] | [[Image:Denon DN-MC6000 Output.png]] | ||
| − | Running mono, set the output to MONO above and connect one XLR output from the Denon DN-MC6000 to the [[L1%C2%AE_Model_II#Analog_Input|Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input|Model 1S Analog input]] | + | Running mono, set the output to MONO above and connect one XLR output from the Denon DN-MC6000 to the [[L1%C2%AE_Model_II#Analog_Input|Model II Analog input]] or [[L1%C2%AE_Model_1S#Analog_Input|Model 1S Analog input]]. Set the input trim so that you have a solid green signal on the Signal/Clip light. If you see red, turn down the trim. |
| + | |||
[[Image:Model II Analog Input Trim.png]] | [[Image:Model II Analog Input Trim.png]] | ||
| Line 75: | Line 76: | ||
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors. | ||
| + | |||
| + | ---- | ||
| + | [[Category:Denon]] | ||
| + | [[Category:Mixer]] | ||
Revision as of 15:30, 8 February 2014
| Suggestions for connecting the Denon DN-MC6000 Professional DJ Multi-controller to an L1® Model 1S, Model II, or Compact. |
Mono
See the diagram below (from Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)
Running mono, set the output to MONO above and connect one XLR output from the Denon DN-MC6000 to the Model II Analog input or Model 1S Analog input. Set the input trim so that you have a solid green signal on the Signal/Clip light. If you see red, turn down the trim.
With a cable like this:
Technical Description:
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
The Female XLR end is wired through to the 1/4" Male TRS end as follows:
- Pin One FXLR to Sleeve of MTRS
- Pin Two FXLR to Tip of MTRS
- Pin Three FXLR to Ring of MTRS
The 1/4" MTRS end is an EWI model P292S-BKG
The FXLR end is an EWI model ES3FB-GDP
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.
Stereo
See the diagram below (from Denon DN-MC6000 Professional DJ Multi-controller manual: Page 10)
Running stereo with two L1®s, set the output to STEREO above and connect one cable from each output to a Model II Analog input or Model 1S Analog input
With a cable like this:
Technical Description:
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
The Female XLR end is wired through to the 1/4" Male TRS end as follows:
- Pin One FXLR to Sleeve of MTRS
- Pin Two FXLR to Tip of MTRS
- Pin Three FXLR to Ring of MTRS
The 1/4" MTRS end is an EWI model P292S-BKG
The FXLR end is an EWI model ES3FB-GDP
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.