Difference between revisions of "Template:T4S Pan Aux"
(Created page with "{{T4S T8S icon}} This is an overview of using the Aux Outputs on the T4S and T8S ToneMatch® mixers. You can use the Aux outputs for monitors, remote speakers, or recording....") |
m |
||
| (4 intermediate revisions by the same user not shown) | |||
| Line 5: | Line 5: | ||
[[File:T4S Aux Output.png|link=|800px]] | [[File:T4S Aux Output.png|link=|800px]] | ||
| + | |||
| + | ; Notes about the PAN/AUX display | ||
| + | The default view for PAN/AUX on the rotary selector is PAN. As a result: | ||
| + | * When you turn the rotary selector away from PAN/AUX, when you turn back, the display will show PAN. But the Aux settings haven't changed. | ||
| + | * When you change channels with the CH Edit buttons, the display will show PAN. But the Aux settings haven't changed. | ||
| + | * For both cases above, to return to the AUX display, press the MENU button (left most button under the display) and rotate to AUX. Your previous settings for PAN are preserved. | ||
;Setting up monitors example | ;Setting up monitors example | ||
| Line 18: | Line 24: | ||
| − | Select a Channel you want to direct to one of the Aux outputs. In the image below the Channel 1 CH Edit button is selected. | + | Select a Channel you want to direct to one of the Aux outputs. '''Note: You can send up more than one Channel to each Aux output''' |
| + | |||
| + | In the image below the Channel 1 CH Edit button is selected. | ||
Turn the Rotary Selector to PAN/AUX | Turn the Rotary Selector to PAN/AUX | ||
| Line 31: | Line 39: | ||
This is how it looks on the T8S when you turn the menu far enough to see all four Aux Outputs. On the T4S there are two Aux Outputs. | This is how it looks on the T8S when you turn the menu far enough to see all four Aux Outputs. On the T4S there are two Aux Outputs. | ||
| − | <!-- | + | <!-- --> |
| + | |||
[[File:Pan Aux 3.jpg|link=|800px]] | [[File:Pan Aux 3.jpg|link=|800px]] | ||
| Line 42: | Line 51: | ||
[[File:Pan Aux 5.jpg|link=|800px]] | [[File:Pan Aux 5.jpg|link=|800px]] | ||
| − | - | + | ;Example - Create a Monitor Mix using Aux1 |
| + | |||
| + | {{T4S Aux1 Example}} | ||
---- | ---- | ||
[[Category:T4S]] | [[Category:T4S]] | ||
[[Category:T8S]] | [[Category:T8S]] | ||
Latest revision as of 19:04, 21 July 2023
This is an overview of using the Aux Outputs on the T4S and T8S ToneMatch® mixers. You can use the Aux outputs for monitors, remote speakers, or recording.
The steps are the same for the T4S and T8S.
- Notes about the PAN/AUX display
The default view for PAN/AUX on the rotary selector is PAN. As a result:
- When you turn the rotary selector away from PAN/AUX, when you turn back, the display will show PAN. But the Aux settings haven't changed.
- When you change channels with the CH Edit buttons, the display will show PAN. But the Aux settings haven't changed.
- For both cases above, to return to the AUX display, press the MENU button (left most button under the display) and rotate to AUX. Your previous settings for PAN are preserved.
- Setting up monitors example
Connect your monitors to the T4S Aux Outputs. On the T4S you have two Aux Outputs. You can direct any channel to one of the Aux Outputs to create a monitor mix. As you assign a channel to an Aux Output, you can set the level and make the Aux send from the channel:
- Dry : After Preamp
- The only control that has an effect on the signal is the channel trim.
- Pre : With EQ and FX
- All settings for Preset, zEQ, ParaEQ, effects are sent through to the Aux output. The volume is controlled by the Level setting in this menu. Volume is not affected by the channel volume control. Reverb available for Aux 1 output only.
- Post : After Fader
- The volume is controlled by the channel volume control.
Select a Channel you want to direct to one of the Aux outputs. Note: You can send up more than one Channel to each Aux output
In the image below the Channel 1 CH Edit button is selected.
Turn the Rotary Selector to PAN/AUX
Turn the leftmost button under the display Menu to see your options. You can choose Pan, Aux Input, or one of the Aux Outputs
This is how it looks on the T8S when you turn the menu far enough to see all four Aux Outputs. On the T4S there are two Aux Outputs.
In this picture we have chosen to direct Channel 1 to Aux 1. The level is 50% and the Tap is set to Pre
In this picture, Aux 1 is selected and you can choose if you want the Tap point to be Dry, Pre, or Post
- Example - Create a Monitor Mix using Aux1
- How do I send the performance mix to the Master Outputs and a different mix (different levels) to a monitor (Aux1).
In this example, we will send:
- Channel 1 (Microphone) to Aux 1
- Channel 2 (Guitar) to Aux 1
- Initially the mix will be the same for Aux1 as to the Master Output (ToneMatch port or Master Output(s)
- Then we will change the relative levels of the Channel 1 and Channel 2