Difference between revisions of "TC-Helicon VoiceLive 3 to Compact"
m (New page: {{TC-Helicon to L1® |L1=Compact |Model parameter 1= Compact Channel 1 |Model parameter 2= Compact Channel 2 |TCH=[http://www.tc-helicon.com...) |
m (fix image) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 4: | Line 4: | ||
|Model parameter 2= [[Compact#Channel_2|Compact Channel 2]] | |Model parameter 2= [[Compact#Channel_2|Compact Channel 2]] | ||
|TCH=[http://www.tc-helicon.com/products/voicelive-3/ VoiceLive 3] | |TCH=[http://www.tc-helicon.com/products/voicelive-3/ VoiceLive 3] | ||
| + | |TCH Image = [[File:Tch-voicelive-3-floor.jpg |link=http://www.tc-helicon.com/products/voicelive-3| 300px |TC-Helicon VoiceLive 3]] | ||
| + | |TCH Additional Note = The VoiceLive 3 does not have a master volume level control. So you will need to control overall level at the Compact. | ||
| + | |||
}} | }} | ||
---- | ---- | ||
[[Category:Compact]] | [[Category:Compact]] | ||
[[Category:TC-Helicon]] | [[Category:TC-Helicon]] | ||
| + | [[Category:VoiceLive 3]] | ||
Latest revision as of 21:56, 28 March 2017
The VoiceLive 3 has two outputs available (Vocal and Guitar) but I choose the LEFT output and run MONO so that I can make the connection with one cable. I don't use Compact Channel 1 when I'm using the VoiceLive 3.
I prefer to use an adapter (XLR to ¼ inch jack) from the VoiceLive 3 left out - to Compact Channel 2. That way you don't have to work around the Compact's internal microphone Preset.
There's MIX button on the VoiceLive 3 that brings up a screen where it's easy to control the relative volumes. Vocal volume is set. You can raise and lower the other inputs on the VoiceLive 3. The VoiceLive 3 does not have a master volume level control. So you will need to control overall level at the Compact.. And it's nice to use just one cable from the VoiceLive 3 to the Compact. This also keeps the Compact Channel 1 free in case I need to plug in another microphone.
I use an adapter like this
| Neutrik NA3FJ XLR to ¼ inch jack Tip-Ring-Sleeve female | or | Planet Waves XLR female to ¼ inch jack Tip-Ring-Sleeve female |
|
|
|
WITH
| Balanced ¼ inch jack Tip-Ring-Sleeve cable | or | Unbalanced ¼ inch jack Tip-Sleeve cable |
|
|
|
OR a longer version of a cable like this:
Technical Description:
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
The Female XLR end is wired through to the 1/4" Male TRS end as follows:
- Pin One FXLR to Sleeve of MTRS
- Pin Two FXLR to Tip of MTRS
- Pin Three FXLR to Ring of MTRS
The 1/4" MTRS end is an EWI model P292S-BKG
The FXLR end is an EWI model ES3FB-GDP
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.
TO