Difference between revisions of "Template:ToneMatch Power Supply"
(created template) |
m |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | ToneMatch® Audio Engine power supply. This is the power supply for the {{ToneMatch Mixer}}. You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, | + | ToneMatch® Audio Engine power supply. |
| + | |||
| + | This is the power supply for the {{ToneMatch Mixer}}. | ||
| + | |||
| + | ==== Not Required with {{L1P}} ==== | ||
| + | The {{L1P}} systems have a ToneMatch port that can supply power to any ToneMatch mixer. | ||
| + | |||
| + | |||
| + | ==== Required with Earlier Systems except {{Model II}} ==== | ||
| + | |||
| + | You will need this to power your {{ToneMatch Mixer}} when running with an {{Compact}}, {{S1}}, {{Classic}}, {{Model I}}, or non-Bose equipment. You will need a one of these if you have two {{ToneMatch Mixer}}s running into a single {{Model II nl}} or {{Model 1S nl}}. — details below the picture. | ||
[[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]] | [[File:L1 tonematch powersupply acc bl lg.jpg|link=https://www.bose.com/en_us/products/speakers/speaker_accessories/l1_tonematch_powersupply_acc.html#v=l1_tonematch_powersupply_acc_black|100px|T1 ToneMatch® Audio Engine power supply]] | ||
| Line 14: | Line 24: | ||
See: [[T1 ToneMatch® Audio Engine / Connections to Model II|Connecting Two T1®s to a Model II]] for details. | See: [[T1 ToneMatch® Audio Engine / Connections to Model II|Connecting Two T1®s to a Model II]] for details. | ||
| + | |||
| + | |||
| + | ---- | ||
| + | If you disassemble the Ethercon connector (not recommended), it's tricky to reassemble it. | ||
| + | |||
| + | [[File:NE8MX-B-1.jpg|400px]] | ||
| + | |||
| + | |||
| + | Note: There are small guides on the grey piece that slide into the slots in the barrel. | ||
| + | |||
| + | [[File:NE8MX-B-12.jpg|400px]] | ||
| + | |||
| + | |||
| + | [[Media:BDA 564 - etherCON NE8MX-1 & NE8MX-B-1 - RJ45 cable connector carrier.pdf]] | ||
| + | |||
| + | ---- | ||
| + | Close up of the connector that goes to the {{ToneMatch Mixer}}, just in case you damage the cable and have to replace the connector. | ||
| + | |||
| + | Note: The picture is taken with the flat side facing the camera. The release clip is on the other side. | ||
| + | |||
| + | [[Image:T1 Power Supply RJ 45 Connector.jpg|400px|Close up of the RJ45 connector]] | ||
| + | |||
---- | ---- | ||
[[Category:T1]] | [[Category:T1]] | ||
| + | [[Category:T4S]] | ||
| + | [[Category:T8S]] | ||
| + | [[Category:Connections]] | ||
[[Category:Bose Link]] | [[Category:Bose Link]] | ||
Latest revision as of 17:46, 6 December 2020
ToneMatch® Audio Engine power supply.
This is the power supply for the ToneMatch Mixer[1].
Not Required with L1 Pro[2]
The L1 Pro[2] systems have a ToneMatch port that can supply power to any ToneMatch mixer.
Required with Earlier Systems except L1 Model II
You will need this to power your ToneMatch Mixer[1] when running with an L1 Compact, S1 Pro System, L1 Classic, L1 Model I, or non-Bose equipment. You will need a one of these if you have two ToneMatch Mixer[1]s running into a single L1® Model II or L1® Model 1S. — details below the picture.
Click image above for purchasing details.
If you connect your T1 ToneMatch® Audio Engine to a L1 Model II or L1 Model 1S then the T1 ToneMatch® Audio Engine draws its power through the ToneMatch® cable.
If you connect your T1 ToneMatch® Audio Engine to an an L1 Classic, L1 Model I or L1 Compact or non-Bose equipment then you will need the T1 ToneMatch® Audio Engine power supply
If you are attaching two T1 ToneMatch® Audio Engines to a single L1® Model II then you will need this power supply to support the second T1® - the one connected to the Power Stand Analog Input.
See: Connecting Two T1®s to a Model II for details.
If you disassemble the Ethercon connector (not recommended), it's tricky to reassemble it.
Note: There are small guides on the grey piece that slide into the slots in the barrel.
Media:BDA 564 - etherCON NE8MX-1 & NE8MX-B-1 - RJ45 cable connector carrier.pdf
Close up of the connector that goes to the ToneMatch Mixer[1], just in case you damage the cable and have to replace the connector.
Note: The picture is taken with the flat side facing the camera. The release clip is on the other side.
- ↑ 1.0 1.1 1.2 1.3 T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine
- ↑ 2.0 2.1 L1 Pro 8, L1 Pro 16, L1 Pro 32