Difference between revisions of "L1 Pro to L1 Compact"
(Created page with "{{L1 Pro icon}} {{Compact icon}} To connect an L1 Pro system to an {{Compact}} as a monitor or an extension of the loudspeaker #Use an XLR female to 1/4 inch (6.3 mm) Tip-Rin...") |
m |
||
| (One intermediate revision by the same user not shown) | |||
| Line 7: | Line 7: | ||
;Note: | ;Note: | ||
| − | The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}). | + | The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for {{ToneMatch Mixers}}). The Line Out sends a signal that matches what you hear from the L1 Pro. As you raise or lower the volume (and make other changes to the sound), this changes the output at the Line Out (except as noted in the next paragraph). |
The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref> | The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. <ref>[https://www.facebook.com/groups/BoseL1/permalink/10159715041622446/?comment_id=10159715092547446 Craig Small - Bose]</ref> | ||
| Line 14: | Line 14: | ||
[[File:L1 Pro8 to L1 Compact Daisy.jpg|400px|L1 Pro Daisy S1 Pro Chain]] | [[File:L1 Pro8 to L1 Compact Daisy.jpg|400px|L1 Pro Daisy S1 Pro Chain]] | ||
| + | |||
| + | Note; | ||
| + | ; L1 Compact Louder than the First | ||
| + | Because the output level of the L1 Pro Line Out is post-fader (see above) is higher than the original source. If you set the volume control on the L1 Compact to the same settings as the first L1 Pro, the L1 Compact may will be louder. Two get the levels the same, | ||
| + | # Turn down the volume on the L1 Compact | ||
| + | # Set the level you want on the L1 Pro | ||
| + | # Set the volume on the L1 Compact to suit the application. Do that by ear. | ||
---- | ---- | ||
Latest revision as of 11:43, 3 February 2023
To connect an L1 Pro system to an L1 Compact as a monitor or an extension of the loudspeaker
- Use an XLR female to 1/4 inch (6.3 mm) Tip-Ring-Sleeve to connect the L1 Pro Line Out to the L1 Compact Channel two (DO NOT USE channel 1 XLR)
- Set the ToneMatch switch to Line Level (down position)
- Set the volume on the L1 Compact to 10:00 o'clock and then adjust to suit the application. If you see solid red on the L1 Compact turn down the channel volume.
- Note
The L1 Pro Line Out is post-fader. That is, it is the combined signal of all inputs and ToneMatch processing, EQ and Reverb. That includes inputs, 1, 2, 3, Bluetooth, and ToneMatch Port (used for T4S/T8S ToneMatch® Mixers). The Line Out sends a signal that matches what you hear from the L1 Pro. As you raise or lower the volume (and make other changes to the sound), this changes the output at the Line Out (except as noted in the next paragraph).
The Line Out is pre-System EQ. That is, the signal at the Line Out is flat. It is not affected by the setting of the System EQ switch. [1]
This applies to any L1 Pro system (L1 Pro8, L1 Pro16, L1 Pro32).
Note;
- L1 Compact Louder than the First
Because the output level of the L1 Pro Line Out is post-fader (see above) is higher than the original source. If you set the volume control on the L1 Compact to the same settings as the first L1 Pro, the L1 Compact may will be louder. Two get the levels the same,
- Turn down the volume on the L1 Compact
- Set the level you want on the L1 Pro
- Set the volume on the L1 Compact to suit the application. Do that by ear.