Difference between revisions of "Mixer to Two L1 Model II"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m (1/4 inch (6.3 mm) Tip-Ring-Sleeve Outputs)
m
Line 4: Line 4:
 
Connect a third party mixer to two {{Model II}}s.  
 
Connect a third party mixer to two {{Model II}}s.  
  
Most modern mixers have [[Balanced / Unbalanced|balanced]] outputs.  
+
Most modern mixers have [[Balanced vs Unbalanced|balanced]] outputs.  
  
These will be  
+
These will be '''XLR''' <br>[[File:Yamaha mg10xu outputs XLR.jpg|300px]]
 
 
XLR
 
 
 
[[File:Yamaha mg10xu outputs XLR.jpg|400px]]
 
  
 
or  
 
or  
  
1/4 inch (6.3 mm) Tip-Ring-Sleeve  
+
'''1/4 inch (6.3 mm) Tip-Ring-Sleeve'''<br>[[File:Yamaha mg10xu outputs 14trs.jpg|300px]]
 
 
[[File:Yamaha mg10xu outputs 14trs.jpg|400px]]
 
  
 
     </div>
 
     </div>

Revision as of 21:13, 6 April 2019

Connect a Third Party Mixer to Two L1 Model II

XLR Outputs

Mixer to L1 Model II XLR.jpg


The output from the Third Party Mixer is a balanced mono XLR and the input on the L1 Model II is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve so use a cable like this.

XLR Female to 1/4" Male TRS  Cable.

XLR Female to 1/4" Male TRS Cable



1/4 inch (6.3 mm) Tip-Ring-Sleeve Outputs

Mixer to L1 Model II 14trs.jpg


The output from the Third Party Mixer is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve and the input on the L1 Model II is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve so use a cable like this.

1/4" Male TRS to 1/4" Male TRS  Cable.

1/4" TRS Balanced Patch Cable (audiopile.net)



L1 Model II Gain Staging

For each L1 Model II


L1 Model II Analog Input

The Analog input is a 1/4 inch (6.3 mm) Tip-Ring-Sleeve balanced input jack.

Model 1S Analog Input Detail.png


Analog input trim (volume, or gain) control

Setting the trim level on the Model II Power Stand is a one-time step. Once you have matched the output of the ToneMatch mixer to the input of the L1 you don't need to adjust it again.

Model II Analog Input Trim.png

T4S/T8S ToneMatch Mixers
  1. Connect the source device Main Output to the L1 Model II Analog Input
  2. Set the Analog Input trim to 9:00 o'clock. Control the volume with the Master Volume on the ToneMatch mixer.
    Model 1S/II Analog Input for T4S/T8S
    If you set the input trim higher, you will have excessive line noise.
  3. If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.
For third-party mixers
  1. Set the Trim control on the power stand to the 0 (zero) position.
  2. Connect the third-party mixer Main Output to the L1 Model II Analog Input
  3. Adjust the volume of the third-party Main Output to the reference or nominal output level.
    • On analog consoles this may be marked as unity or 0 dB.
    • On digital consoles this may be marked as -18 dBFS[1][2]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location[3].
    • Refer to the manual for the third-party for details.
  4. If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.

Model 1S Analog Input