Difference between revisions of "T8S to L1 Model II"
m |
m |
||
| Line 1: | Line 1: | ||
| + | <div class="tocdiv"> | ||
| + | <div>__TOC__</div> | ||
| + | <div><h2>Introduction</h2> | ||
| + | Here is how to connect a {{T8S}} to two {{Model II}}s. | ||
| + | </div> | ||
| + | </div> | ||
| + | |||
== Connect the T8S to {{Model II}} == | == Connect the T8S to {{Model II}} == | ||
| − | + | === 1/4 inch (6.3 mm) Tip-Ring-Sleeve Outputs === | |
[[File:T8S to L1 Model II.jpg|600px]] | [[File:T8S to L1 Model II.jpg|600px]] | ||
| Line 9: | Line 16: | ||
Set the {{Model II}} Analog Input Trims to about 9:00 o'clock. | Set the {{Model II}} Analog Input Trims to about 9:00 o'clock. | ||
| − | + | === XLR Outputs === | |
| − | {{ | + | |
| − | + | [[File:T8S XLR to L1 Model II.jpg|600px]] | |
| + | |||
| + | {{Balanced XLR |Source= [[T8S]]|Target= {{Model II}} | ||
| + | }} | ||
== L1 Model II Gain Staging == | == L1 Model II Gain Staging == | ||
Revision as of 22:11, 12 March 2019
Introduction
Here is how to connect a T8S ToneMatch mixer to two L1 Model IIs.
Connect the T8S to L1 Model II
1/4 inch (6.3 mm) Tip-Ring-Sleeve Outputs
The output from the T8S ToneMatch mixer is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve and the input on the L1 Model II is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve so use a cable like this.
.
1/4" TRS Balanced Patch Cable (audiopile.net)
Connect the ToneMatch Power Supply to the T8S ToneMatch mixer for power.
Set the L1 Model II Analog Input Trims to about 9:00 o'clock.
XLR Outputs
The output from the T8S is a balanced mono XLR and the input on the L1 Model II is a balanced mono 1/4 inch (6.35 mm) Tip-Ring-Sleeve so use a cable like this.
.
XLR Female to 1/4" Male TRS Cable
L1 Model II Gain Staging
For each L1 Model II
L1 Model II Analog Input
The Analog input is a 1/4 inch (6.3 mm) Tip-Ring-Sleeve balanced input jack.
Analog input trim (volume, or gain) control
Setting the trim level on the Model II Power Stand is a one-time step. Once you have matched the output of the ToneMatch mixer to the input of the L1 you don't need to adjust it again.
T4S/T8S ToneMatch Mixers
- Connect the source device Main Output to the L1 Model II Analog Input
- Set the Analog Input trim to 9:00 o'clock. Control the volume with the Master Volume on the ToneMatch mixer.
If you set the input trim higher, you will have excessive line noise. - If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.
For third-party mixers
- Set the Trim control on the power stand to the 0 (zero) position.
- Connect the third-party mixer Main Output to the L1 Model II Analog Input
- Adjust the volume of the third-party Main Output to the reference or nominal output level.
- If the Signal/Clip indicator glows red, decrease the Trim level so that it glows only green or yellow.
