Using a Different Sub

Using a Different Sub

The following notes are compiled from a discussion on the Bose Community Message Boards. Using a Different Sub

Question

What are the problems or benefits of pluging in a different sub cabinet to the PAS. It it even possible or feasable. Say you have a 4 ohm 250 watt EV sub with a 15 in speaker and you pluged into it instead of the B1. What could you expect and is there any possible damage you could cause.

or could you use that instead of a second B1 for more bottom.

Breaking this down into several smaller questions we get:

Q: Can you cause any damage to the Power Stand or the speakers by using a third-party loudspeaker?

A: The powered Bass Output of the Power Stand is rated to provide

• 125 Watts at 8 ohms
• 250 Watts at 4 ohms

Be careful that whatever you connect to the Power Stand Bass Output is compatible with this. Note: On the L1™ Classic, this connection is called Amp3 Out, and in later versions that connection has a blue background.

Q: What is the Crossover Point for the powered Power Stand Bass Output?

A: This depends on if there are if there are B1 Bass Modules attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.

• 110 Hz when there are no B1 Bass Modules connected to the Power Stand Bass Output.
• 180 Hz if there is something (even a dummy plug) is inserted into the Bass Line Out jack on the Power Stand.
• 180 Hz when there is one (or two) B1 Bass Modules connected to the Power Stand Bass Output. If one or two B1 Bass Modules are detected then proprietary EQ is applied to the output to optimize the performance of the B1s.

Q: What is the Frequency for the unpowered Power Stand Bass Line Out?

A: This depends on if there are if there are B1 Bass Modules attached. There is a hard cut off at the frequencies noted, for the signal provided to the Cylindrical Radiator® loudspeaker.

• 40-180Hz Band Pass when no B1 Bass Modules are attached to the Power Stand
• 40-180Hz If any B1 Bass Modules are connected to the Power Stand then proprietary EQ is applied to the output to optimize the performance of the B1s. In other words, if there are B1 Bass Modules connecte directly to the Power Stand, the the Bass Line Out is optimized for more B1 Bass Modules as would be appropriate when using the PackLite^® power amplifier model A1 Extended Bass Package.

Q: Can I mix B1 Bass Modules with other subs?

A: This is not recommended.

Q: Why does Bose call the B1 a Bass Module instead of a sub.

A: Here is the story as far as I can tell: Originally the term "subwoofer" was used in movie theater sound systems. There the standard is still 5 full-range channels and one subwoofer channel. The subwoofer channel has signifcant spectral overlap with the main channels. Typically the main channels start at 40 Hz or 50 Hz and the subwoofer ranges from 30ish up to about 120 Hz. The Subwoofer can produce some serious bass level, but fidelity is not much of an requirement, as they are mainly used for sound effects (explosion, the ominous rumble, etc.)

In contrast a multi-way PA of the time had between 2 and 4 different speakers all dedicated to specific non-overlapping frequency areas. The bass produces were typically called bass-bins or bass cabinets and not subwoofers, as they actually do something different.

Bose was probably one of the first (if not the first), that made the split system (single bass box, multiple small satelite) commercially successful for home use with the AM-5 speaker. As commonplace as it is today, at the time it was a pretty radical idea and many, many audio experts stated that can't possibly work (sounds familiar ?). Anyway, as we tried to name the black bass-producing device, we felt bass module was a good choice as it was functionally different from a subwoofer.

After it turned out, that the concept did indeed work many more manufactures turned out products in the same category and in the process subwoofer became the common term. Maybe the marketing departments wanted to imply that it's similar to a real movie sound system, maybe they just didn't know the difference.

So in short, IMO the difference would be a) Subwoofer is a low frequency extension, but the system can also work without it b) Bass module is a integral part of the system with dedicated non-overlapping frequecny range.

Of course, in the end it's just nit-picking and common use defines language more than any technical specification.

Just my 2c

Hilmar

---