Search results

Create the page "Balanced" on this wiki! See also the search results found.

• LR Baggs Session DI to ToneMatch Mixer T1/T4S/T8S
  ...ll give you a balanced<ref>[[Balanced vs Unbalanced]]</ref> connection and balanced connections are preferable to unbalanced connections in most situations.
  4 KB (656 words) - 15:13, 3 February 2020
• L1® Model II
  The Analog input is a ¼ inch balanced input jack. Do not connect a stereo source to this input. The analog input on the Model II is balanced, and will therefore subtract the Left and Right signals on a stereo cable a
  9 KB (1,440 words) - 01:37, 20 May 2021
• International Bluegrass Musicians Association
  ...owed us to run the systems at much lower gain, giving the bands a far more balanced sound everywhere in the room. The separation of the two microphones, magnif ...ated singers and their amps, but by aiming those mics differently we got a balanced sound out into the room.
  16 KB (2,848 words) - 17:51, 14 October 2009
• T1 ToneMatch® Audio Engine / Use without the L1® in Festival Situations
  * Up to four dry balanced direct output signals for the house system. These signals will not contain {{:XLR Male to 1/4 TRS Balanced Cable}}
  5 KB (893 words) - 05:16, 26 March 2017
• Acronyms
  See [[TRS]] and [[Balanced vs Unbalanced]] See related:[[TRS]] and [[Balanced vs Unbalanced]]
  2 KB (387 words) - 20:58, 14 January 2009
• L1® Model 1S
  The Analog input is a ¼ inch balanced input jack. The analog input is balanced, and will therefore subtract the Left and Right signals on a stereo cable a
  8 KB (1,264 words) - 01:56, 20 May 2021
• L1® Model 1S FAQ
  ...ay enables the system to fill an entire room with clear, powerful, tonally balanced sound from a single loudspeaker system. Sound remains consistent even at th ...ss module is a portable, lightweight bass module designed to provide deep, balanced bass for Model 1S and Model II systems. It features two 5.25" high-excursio
  14 KB (2,381 words) - 05:47, 26 March 2017
• T1 ToneMatch® Audio Engine / Connections to Compact
  ...inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} cable, but you will lose up to -6 dB i
  1 KB (186 words) - 11:48, 30 August 2018
• Denon DN-X500
  [[Image:Compact Channel 2 Balanced.png]] ...erting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equip
  2 KB (300 words) - 18:18, 8 February 2014
• Kemper Profiler
  * XLR connection. This is a balanced connection and it is preferable ...r the entire Rig: amp, cabinet, and all effects. You have a choice of XLR (balanced) or quarter-inch TS-jacks (unbalanced). The XLR outputs are protected again
  24 KB (3,721 words) - 12:54, 8 August 2023
• Mixer / Behringer / Europower / PMP6000
  ...lanced 1/4" stereo jacks. Of course, all inputs and outputs work with both balanced and unbalanced connectors. The tape in and outputs are on RCA connectors.
  2 KB (223 words) - 13:15, 28 July 2014
• Stereo Mixer to Mono L1®
  Where possible use a balanced connection between the mixer output and the L1® input. ...e the one above, you can use one of the &frac14; inch jack Tip-Ring-Sleeve balanced outputs. You can pan all the inputs to the LEFT side and use the LEFT outpu
  8 KB (1,188 words) - 23:23, 8 April 2022
• Bose T4S and T8S ToneMatch® Mixers Compared to Bose T1® ToneMatch Audio Engine
  * A single mono channel with two 1/4" (6.3mm) balanced line-level inputs that were immediately converted to mono. * Two 1/4" (6.3mm) balanced line-level inputs
  3 KB (453 words) - 01:38, 17 May 2021
• T8S Analog vs Digital Connection to L1® Model II or L1® Model 1S
  ...While the digital connection is nice, your experience will be fine with a balanced TRS connection between the T8S and L1 Model II.'' * Balanced 25-foot cable from the T4S Left Channel analog output to the&nbsp; L1® Mod
  3 KB (541 words) - 11:02, 28 February 2018
• T8S to L1 Model II
  {{Balanced TRS from T8S to L1 Model II}} {{Balanced XLR |Source= [[T8S]]|Target= {{Model II}}
  1 KB (231 words) - 12:31, 10 April 2019
• T1 to T8S to Two L1 Model II
  {{Balanced TRS from T1 to T8S}} {{Balanced TRS from T1 to T8S}}
  2 KB (290 words) - 12:39, 10 October 2019
• T1 ToneMatch® Audio Engine / Connections to S1 Pro
  ...inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} cable, but you will lose up to -6 dB i
  1 KB (182 words) - 12:02, 23 February 2019
• S1 Pro as Monitor with T1
  ...inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} , but you will lose up to -6 dB in sig
  3 KB (433 words) - 22:23, 16 November 2019
• S1 Pro as Monitor with Third Party Mixer and L1
  ...inputs are '''balanced'''. For best results use a {{1/4 TRS}} cable for a balanced connection. You can use a {{1/4 TS}} , but you will lose up to -6 dB in sig
  2 KB (357 words) - 22:23, 16 November 2019
• PRS JA-15
  ...arity of the figured maple back creates a resonance in this guitar that is balanced with tonal clarity, and the simple control layout makes the JA-15 a joy to ...atured on the JA-15, including two 53/10™ bass pickups to give a smooth, balanced tone, the all new thin, hard and crystal clear “V12” finish, and the tw
  13 KB (1,896 words) - 11:13, 27 July 2022

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)