Search results

Create the page "Balanced" on this wiki! See also the search results found.

• PackLite® power amplifier Model A1
  ...he MASTER you'll see that all of that power is available to you, just in a balanced fashion.
  12 KB (2,063 words) - 13:56, 21 September 2023
• B1 Bass Module
  * Designed to provide deep, balanced bass for Model 1S and Model II systems
  10 KB (1,586 words) - 00:10, 17 February 2019
• Mixer / Mackie / DFX6
  === XLR Balanced +4 ===
  666 bytes (84 words) - 03:12, 21 December 2008
• Pad
  ...wish to achieve. Bose recommends -20dB of attenuation to bring a hot +4dBu balanced line level signal down to a voltage that the Bose PS1 (Classic) Mic inputs
  5 KB (853 words) - 17:26, 14 May 2017
• Hearing Yourself with the L1®
  * In a more general sense, if things are balanced, then everyone should be able to hear themselves AND everyone else. If that
  3 KB (612 words) - 18:10, 26 March 2017
• Feedback / Microphone
  A microphone that is not tonally balanced requires expertise and sophisticated equipment to equalize optimally. ToneM
  16 KB (2,433 words) - 20:03, 1 July 2023
• Stage Layouts / Four Systems
  This is nice balanced layout that we use on stages 20-25 feet wide.
  2 KB (302 words) - 19:11, 4 January 2009
• White Papers
  high output and full, balanced frequency response. The fact that the MA12 is placed
  4 KB (651 words) - 13:44, 29 March 2017
• Mixer / Behringer / Eurorack / MX1604A
  If want to use the balanced outputs (red) set the button (50) or use ¼ Inch Main Outputs (green)
  1 KB (164 words) - 02:53, 21 December 2008
• PS1 Powerstand Connections/Line Out/XLR
  == Line Outs (XLR balanced) for Channels 1 and 2 ==
  581 bytes (90 words) - 14:46, 31 December 2008
• Hearing the Same Thing
  Bring up the volumes of the instruments so that these are correctly balanced in relation to the vocal.
  4 KB (665 words) - 14:02, 3 December 2006
• PS1 Powerstand / Signal Flow
  * The XLR input is a balanced low impedance input stage with a lot of gain.
  2 KB (295 words) - 16:43, 12 January 2012
• Mixer / Mackie / 1202-VLZ
  * If you want to use the Balanced XLR outputs use the MIC setting in the picture above.
  2 KB (268 words) - 12:28, 18 March 2012
• XLR
  {{:Balanced vs Unbalanced}}
  518 bytes (72 words) - 22:57, 18 July 2007
• Line Noise
  ...hielded wire for all microphones and input cables. Also, use low-impedance balanced microphone cables, which are less susceptible to interference than high-imp
  3 KB (442 words) - 11:07, 8 June 2010
• L1® Model II / FAQ
  Standard, balanced tip-ring-sleeve ¼" cable connects the A1 PackLite® power amplifier to a p
  42 KB (6,832 words) - 05:25, 26 March 2017
• L1® PackLite® A1 Amplifier / FAQ
  Standard, balanced tip-ring-sleeve 1/4" cable connects the A1 PackLite® power amplifier to a
  17 KB (2,728 words) - 05:42, 26 March 2017
• T1 ToneMatch® Audio Engine / Switching Between Instruments
  ...Out to the input of a second T1™ Channel. Use a 1/4" to 1/4" cable, balanced or unbalanced should be fine.
  2 KB (421 words) - 04:21, 26 March 2017
• T1 ToneMatch® Audio Engine / USB / Output Stereo to Two L1®s
  ...pendent of the Master volume. This is why you want to set it to be equally balanced with the Master. You will then be able to control the balance and level fro
  7 KB (1,115 words) - 16:44, 4 September 2023
• T1 ToneMatch® Audio Engine / Connections to Model II
  ...Match® Audio Engine / 1/4 inch Output Connections to L1® Family Members |Balanced}}
  1 KB (231 words) - 04:42, 26 March 2017

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)