Template:TC-Helicon to L1®
Usage:
{{TC-Helicon to L1®
|L1=[[Compact]]
|Model parameter 1= [[Compact#Channel_1|Compact Channel 1]]
|Model parameter 2= [[Compact#Channel_2|Compact Channel 2]]
|TCH=[http://www.tc-helicon.com/products/voicelive-play-gtx/ VoiceLive Play GTX]
|TCH Image = {{#img: image=Voicelive-play-gtx_top.jpg |page=http://www.tc-helicon.com/products/voicelive-play-gtx| height=250px |title=TC-Helicon VoiceLive Play GTX }}
|TCH Additional Note = so I don't have to touch the {{{L1}}} once I'm set up.
}}
Compact
The {{{TCH}}} has two outputs available (Vocal and Guitar) but I choose the LEFT output and run MONO so that I can make the connection with one cable. I don't use Compact Channel 1 when I'm using the {{{TCH}}}.
I prefer to use an adapter (XLR to ¼ inch jack) from the {{{TCH}}} left out - to Compact Channel 2. That way you don't have to work around the {{{L1}}}'s internal microphone Preset.
{{#img: image=Compact_Channel_2_Line_Level.png |page=Compact#Channel_2| width=400px |title=Compact Channel 2}}
There's MIX button on the {{{TCH}}} that brings up a screen where it's easy to control the relative volumes. Vocal volume is set. You can raise and lower the other inputs on the {{{TCH}}}. {{{TCH Additional Note}}}. And it's nice to use just one cable from the {{{TCH}}} to the {{{L1}}}. This also keeps the Compact Channel 1 free in case I need to plug in another microphone.
I use an adapter like this
| Neutrik NA3FJ XLR to ¼ inch jack Tip-Ring-Sleeve female | or | Planet Waves XLR female to ¼ inch jack Tip-Ring-Sleeve female |
|
{{#img: image=NeutrikNA3FJ.jpg |page=http://www.audiopile.net/products/Adaptors_Connectors/NEUTRIK/NA3FJ/NA3FJ_cutsheet.shtml%7C width=300px |title=NA3FJ Neutrik 3 Pin XLR Female to 1/4" TRS Female Locking Barrel Adapter}} |
{{#img: image=XLRTo14female.png |page=http://www.musiciansfriend.com/accessories/planet-waves-xlr-female-to-1-4-female-adapter%7C width=300px |title=xlr female to 1/4 female adapter}} |
WITH
| Balanced ¼ inch jack Tip-Ring-Sleeve cable | or | Unbalanced ¼ inch jack Tip-Sleeve cable |
|
{{#img: image=TRStoTRS.jpg |page=http://www.audiopile.net/products/Mic_Instr_Cables/IP-101/IP-101_cutsheet.shtml%7C width=300px |title=¼ inch jack Tip-Ring-Sleeve }} |
{{#img: image=TSUnbalanced.jpg |page=http://www.audiopile.net/products/Mic_Instr_Cables/GBNC/GBNC_SOON_cutsheet.shtml%7C width=300px |title=¼ inch jack Tip-Sleeve }} |
OR a longer version of a cable like this:
Technical Description:
The EWI MP-105 is a special application adaptor cable for converting XLR to 1/4 TRS. This cable is typically used to plug XLR cord into balanced 1/4" TRS panel jacks commonly found on mixing consoles and processing equipment.
The Female XLR end is wired through to the 1/4" Male TRS end as follows:
- Pin One FXLR to Sleeve of MTRS
- Pin Two FXLR to Tip of MTRS
- Pin Three FXLR to Ring of MTRS
The 1/4" MTRS end is an EWI model P292S-BKG
The FXLR end is an EWI model ES3FB-GDP
The cable itself is constructed with 99.98% pure 22ga. high strand count copper conductors.
TO
{{{Model parameter 2}}}