T8S ToneMatch Mixer Aux Output to S1 Pro

Here's a quick overview of how you can connect a T8S to an S1 Pro

Leave the T8S and S1 Pro turned off until you have things connected
Connect the T8S power supply to the T8
1. Leave the T8S and S1 Pro turned off until you have things connected
2. Connect the T8S power supply to the T8S
3. Connect the T8S Aux Output you are using for the monitor send to S1 Pro channel 1 or 2
  - Use a 1/4 inch Tip-Ring-Sleeve cable for best results
4. On the S1 Pro channel:
  - Turn off the reverb
  - Set both tone controls to the center position
  - Set the channel volume off
5. Turn on the T8S
  - On the T8S
    1. Set the Rotary Selector to PAN/AUX
    2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
    3. Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
6. Connect all your sound sources to the T8S
7. Turn on the S1 Pro
8. Bring up the channel volume on the S1 Pro to about 11:00 o'clock
9. Control the volume using the T8S Master Volume
10. If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T8S
11. Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro
On the S1 Pro System, for each channel you are connecting to the T8S ToneMatch Mixer use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.
S1 Pro+
You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.
Contents
Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer^[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2
Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer^[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer^[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System
1. Turn the channel volume off
2. Connect your sound source
3. Adjust the volume of the source device output to the reference or nominal output level.
  - On analog consoles this may be marked as unity or 0 dB.
  - On digital consoles this may be marked as -18 dBFS^[2]^[3]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location^[4].
  - Refer to the manual for the source device for details.
  - If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.
Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
- XLR (balanced mono)
  - Microphone or Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
  - Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
  - Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
- The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
- The S1 Pro XLR inputs are best suited for microphones.
When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad
XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

Here's a quick overview of how you can connect a T8S to an S1 Pro
1. Leave the T8S and S1 Pro turned off until you have things connected
2. Connect the T8S power supply to the T8S (T8S power supply sold separately)
3. Connect the T8S Right Output to S1 Pro channel 1 or 2
  - Use a 1/4 inch Tip-Ring-Sleeve cable for best results
4. On the S1 Pro channel:
  - Turn off the reverb
  - Set both tone controls to the center position
  - Set the channel volume off
5. Turn on the T8S
  - On the T8S
    1. Set the Rotary Selector to PAN/AUX
    2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
    3. Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
6. Connect all your sound sources to the T8S
7. Turn on the S1 Pro
8. Bring up the channel volume on the S1 Pro to about 11:00 o'clock
9. Control the volume using the T8S Master Volume
10. If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T8S
11. Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro
On the S1 Pro System, for each channel you are connecting to the T8S/T8S ToneMatch® Mixer use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer^[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2
Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer^[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer^[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System
1. Turn the channel volume off
2. Connect your sound source
3. Adjust the volume of the source device output to the reference or nominal output level.
  - On analog consoles this may be marked as unity or 0 dB.
  - On digital consoles this may be marked as -18 dBFS^[5]^[6]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location^[7].
  - Refer to the manual for the source device for details.
  - If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.
Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
- XLR (balanced mono)
  - Microphone or Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
  - Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
  - Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
- The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
- The S1 Pro XLR inputs are best suited for microphones.
When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad
XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

Here's a quick overview of how you can connect a T8S to an S1 Pro
1. Leave the T8S and S1 Pro turned off until you have things connected
2. Connect the T8S power supply to the T8S (T8S power supply sold separately)
3. Connect the T8S Right Output to S1 Pro channel 1 or 2
  - Use a 1/4 inch Tip-Ring-Sleeve cable for best results
4. On the S1 Pro channel:
  - Turn off the reverb
  - Set both tone controls to the center position
  - Set the channel volume off
5. Turn on the T8S
  - On the T8S
    1. Set the Rotary Selector to PAN/AUX
    2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
    3. Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
6. Connect all your sound sources to the T8S
7. Turn on the S1 Pro
8. Bring up the channel volume on the S1 Pro to about 11:00 o'clock
9. Control the volume using the T8S Master Volume
10. If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T8S
11. Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro
On the S1 Pro System, for each channel you are connecting to the T8S/T8S ToneMatch® Mixer use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer^[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2
Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer^[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer^[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System
1. Turn the channel volume off
2. Connect your sound source
3. Adjust the volume of the source device output to the reference or nominal output level.
  - On analog consoles this may be marked as unity or 0 dB.
  - On digital consoles this may be marked as -18 dBFS^[8]^[9]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location^[10].
  - Refer to the manual for the source device for details.
  - If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.
Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
- XLR (balanced mono)
  - Microphone or Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
  - Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
  - Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
- The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
- The S1 Pro XLR inputs are best suited for microphones.
When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad
XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

Here's a quick overview of how you can connect a T8S to an S1 Pro
1. Leave the T8S and S1 Pro turned off until you have things connected
2. Connect the T8S power supply to the T8S
3. Connect the T8S Right Output (or Aux Output if you using the S1 Pro as a monitor) to S1 Pro channel 1 or 2
  - Use a 1/4 inch Tip-Ring-Sleeve cable for best results
4. On the S1 Pro channel:
  - Turn off the reverb
  - Set both tone controls to the center position
  - Set the channel volume off
5. Turn on the T8S
  - On the T8S
    1. Set the Rotary Selector to PAN/AUX
    2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
    3. Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
6. Connect all your sound sources to the T8S
7. Turn on the S1 Pro
8. Bring up the channel volume on the S1 Pro to about 11:00 o'clock
9. Control the volume using the T8S Master Volume
10. If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T8S
11. Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro
On the S1 Pro System, for each channel you are connecting to the T8S/T8S ToneMatch® Mixer use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer^[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2
Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer^[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer^[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System
1. Turn the channel volume off
2. Connect your sound source
3. Adjust the volume of the source device output to the reference or nominal output level.
  - On analog consoles this may be marked as unity or 0 dB.
  - On digital consoles this may be marked as -18 dBFS^[11]^[12]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location^[13].
  - Refer to the manual for the source device for details.
  - If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
4. While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.
Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept
- XLR (balanced mono)
  - Microphone or Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
  - Line-Level inputs
- 1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
  - Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)
When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?
- The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
- The S1 Pro XLR inputs are best suited for microphones.
When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad
XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

S (T8S power supply sold separately)
Connect the T8S Right Output to S1 Pro channel 1 or 2
<img src="" />
- Use a 1/4 inch Tip-Ring-Sleeve cable for best results
  
  <img alt="See the source image" data-reactid="21" src="" style="width: 217px; height: 223px;" width="689" />
On the S1 Pro channel:
- Turn off the reverb
- Set both tone controls to the <g class="gr_ gr_35 gr-alert gr_spell gr_inline_cards gr_run_anim ContextualSpelling multiReplace" id="35" data-gr-id="35">center</g> position
- Set the channel volume off
Turn on the T8S
- On the T8S
  1. Set the Rotary Selector to PAN/AUX
  2. Press the CH EDIT button for each channel you are using and pan the input hard RIGHT
  3. Note: Steps 1 and 2 above are one-time-only. You don't have to change this unless you get another S1 Pro and want to run in stereo
Connect all your sound sources to the T8S
Turn on the S1 Pro
Bring up the channel volume on the S1 Pro to about 11:00 o'clock
Control the volume using the T8S Master Volume
If you see the S1 Pro channel 1 light turning solid red occasionally, turn down the volume on the T8S
Or if you see the S1 Pro channel 1 light turning solid red frequently, turn down the volume on the S1 Pro

</html>

On the S1 Pro System, for each channel you are connecting to the T8S/T8S ToneMatch® Mixer use these settings while you are setting up.

Reverb OFF
Bass at 12:00 o'clock
Treble at 12:00 o'clock
ToneMatch switch OFF

You can adjust the Reverb, Bass, and Treble after you get your basic sound working.

S1 Pro+

You can also connect to the Channel 3 Aux input. For best results, use a 1/4 inch (6.3 mm) Tip-Ring-Sleeve cable.

Gain Staging

Using a Bose device as the source

When connecting a ToneMatch Mixer^[1] or an S1 Pro System Line Out to an S1 Pro System channel 1 or channel 2

Set the volume control to 10:00 o'clock with 1/4 inch (6.3 mm) Tip-Ring-Sleeve

The signal strength from a ToneMatch Mixer^[1] or an S1 Pro System Line Out is sufficient to achieve the maximum usable volume from the S1 Pro System

Control the overall volume from the ToneMatch Mixer^[1] or the first S1 Pro System. If you use an XLR cable, set the volume control to 9:00 o'clock

Using a third-party source (not a Bose device as the source)

For each channel you are using on the S1 Pro System

Turn the channel volume off
Connect your sound source
Adjust the volume of the source device output to the reference or nominal output level.
- On analog consoles this may be marked as unity or 0 dB.
- On digital consoles this may be marked as -18 dBFS^[14]^[15]. The exact value (-18 dBFS to -20 dBFS) may vary depending your location^[16].
- Refer to the manual for the source device for details.
- If the source device does not have metering or indicators, set the output as high as you can without hearing distortion or seeing red indicator lights.
While playing/singing as loud as you will during your performance, bring up the channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.

Combo Inputs

S1 Pro Channels 1 and 2 have combo inputs that accept

XLR (balanced mono)
- Microphone or Line-Level inputs
1/4 inch (6.3 mm) Tip-Ring-Sleeve connection (balanced mono)
- Line-Level inputs
1/4 inch (6.3 mm) Tip-Sleeve connection (unbalanced mono)
- Line-Level inputs and instruments (e.g. guitars, keyboards, guitar processors, loopers)

When using a third-party device (e.g., mixer or another line-level source) should I use the XLR or 1/4 inch inputs?

The S1 Pro 1/4 inch Tip-Ring-Sleeve inputs are best suited for line-level balanced inputs. This is a better match for the signal level.
The S1 Pro XLR inputs are best suited for microphones.

When the S1 Pro Channel input lights hit red or you hear distortion, the signal is clipping and you've reached the maximum usable volume. From the source, if the XLR outputs are line-level and the 1/4 inch Tip-Ring-Sleeve outputs are line-level, it won't matter which type of cable you use. They'll both get the job done, although the volume control setting will be lower with the XLR connection. That doesn't indicate more headroom. The maximum usable volume is the same either way.

Alternate Connection

You can use an XLR cable (mic cable) from a Line Level Source (e.g., L1 Pro, S1 Pro+) to S1 Pro or S1 Pro+ channels 1 or 2 (XLR inputs), but the signal may clip, overload, or be too high to control the volume. To attenuate (reduce) the signal, use a -20 dB or -30 dB Pad

XLR Cable

Pad

Click image for more information about Pads

Connecting a Mixer to an S1 Pro system

Article from Bose Connecting an S1 Pro to a mixer

↑ ^1.00 ^1.01 ^1.02 ^1.03 ^1.04 ^1.05 ^1.06 ^1.07 ^1.08 ^1.09 ^1.10 ^1.11 ^1.12 ^1.13 ^1.14 T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine
↑ dBFS
↑ dBU vs dBFS
↑ dBFS Analog Levels
↑ dBFS
↑ dBU vs dBFS
↑ dBFS Analog Levels
↑ dBFS
↑ dBU vs dBFS
↑ dBFS Analog Levels
↑ dBFS
↑ dBU vs dBFS
↑ dBFS Analog Levels
↑ dBFS
↑ dBU vs dBFS
↑ dBFS Analog Levels

[TM_Mixer-1] 1.00 ^1.01 ^1.02 ^1.03 ^1.04 ^1.05 ^1.06 ^1.07 ^1.08 ^1.09 ^1.10 ^1.11 ^1.12 ^1.13 ^1.14 T4S ToneMatch mixer or T8S ToneMatch mixer or T1 ToneMatch Audio Engine

[2] BFS

[3] BU vs dBFS

[4] BFS Analog Levels

[5] BFS

[6] BU vs dBFS

[7] BFS Analog Levels

[8] BFS

[9] BU vs dBFS

[10] BFS Analog Levels

[11] BFS

[12] BU vs dBFS

[13] BFS Analog Levels

[14] BFS

[15] BU vs dBFS

[16] BFS Analog Levels

[1]

[2]

[3]

[4]

[5]

[6]

[7]

[8]

[9]

[10]

[11]

[12]

[13]

[14]

[15]

[16]

T8S ToneMatch Mixer Aux Output to S1 Pro

Contents

Gain Staging

Combo Inputs

Alternate Connection

Connecting a Mixer to an S1 Pro system

Gain Staging

Combo Inputs

Alternate Connection

Connecting a Mixer to an S1 Pro system

Gain Staging

Combo Inputs

Alternate Connection

Connecting a Mixer to an S1 Pro system

Gain Staging

Combo Inputs

Alternate Connection

Connecting a Mixer to an S1 Pro system

Gain Staging

Combo Inputs

Alternate Connection

Connecting a Mixer to an S1 Pro system

Navigation menu

Personal tools

Namespaces

Variants

Views

More

Search

Navigation

home

Current Models

Legacy Models

Application Guides

Community

Tools