Difference between revisions of "Mixer / Yamaha / MG124 CX"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m
m (Settings on the L1® Input Panel)
 
(5 intermediate revisions by the same user not shown)
Line 1: Line 1:
To use a Yamaha MG124 CX Mixer with the {{Model II}}
+
<table><tr>
 +
<td valign="top" width="250">__TOC__</td>
 +
<td valign="top">To use a Yamaha MG124 CX Mixer with the {{Model II}}
 +
</td>
 +
</tr></table> 
 +
 
 +
 
 
==== Overview ====
 
==== Overview ====
 
On the mixer
 
On the mixer
* pan all the inputs hard LEFT
+
* Pan all the inputs hard LEFT
* run a line out of the LEFT output  to the Model II Power Stand  Analog input (cable details below)
+
* Run a line out of the LEFT output  to the Model II Power Stand  Analog input (cable details below)
 
[[Image:YamahaMG124 to Model II Power Stand Analog Input.png]]
 
[[Image:YamahaMG124 to Model II Power Stand Analog Input.png]]
 +
 +
==== Settings on the L1® Input Panel ====
 +
Start off with the Input Trim at '''3''' and adjust if necessary so that the Signal/Clip light stays green most of the time. Occasional flickers of yellow are okay. If it is flickering or solid red, turn down the Input Trim.
 +
 +
[[Image:ModelIIInputsForTwoLT1.png]]
  
 
==== Cable Details ====
 
==== Cable Details ====
Line 30: Line 41:
 
</td></tr></table>
 
</td></tr></table>
  
 +
=== Documents ===
 +
* {{Model II}}
 +
* [http://download.yamaha.com/api/asset/file?language=en&site=countrysite-master.prod.exp.yamaha.com&asset_id=8043 Yamaha MG124CX/MC124 Owner's Manual]
  
 +
[[Image:YamahaMG124 Output.png]]
 
----
 
----
 
[[Category:Mixer]]
 
[[Category:Mixer]]
 
[[Category:Yamaha]]
 
[[Category:Yamaha]]

Latest revision as of 14:02, 19 September 2012

To use a Yamaha MG124 CX Mixer with the L1 Model II


Overview

On the mixer

  • Pan all the inputs hard LEFT
  • Run a line out of the LEFT output to the Model II Power Stand Analog input (cable details below)

YamahaMG124 to Model II Power Stand Analog Input.png

Settings on the L1® Input Panel

Start off with the Input Trim at 3 and adjust if necessary so that the Signal/Clip light stays green most of the time. Occasional flickers of yellow are okay. If it is flickering or solid red, turn down the Input Trim.

ModelIIInputsForTwoLT1.png

Cable Details

¼ inch jack inch to ¼ inch

This mixer has ¼ inch jack balanced outputs. Any of the cables shown below should work.


¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)

The output of this mixer is balanced, and the input on the Model II Power Stand is also balanced, so this is the preferred method.

Tip-Ring-Sleeve to Tip-Ring-Sleeve

¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)

Tip-Sleeve to Tip-Sleeve

¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)

Tip-Ring-Sleeve to Tip-Sleeve


Documents

YamahaMG124 Output.png