Search results

Create the page "Settings" on this wiki! See also the search results found.

• Recording USB Dry
  ...nd a DRY (without any effects) signal to the computer while retaining any settings you prefer to hear for monitoring or performance. * Set Aux settings as shown here.
  856 bytes (146 words) - 14:45, 7 February 2014
• ToneMatch Mixer Scenes
  You can save all your ToneMatch Mixer settings as a Scene.  Think of it as a snapshot. You can have up to ten User Sc A Scene captures all your settings except input trim and channel and master volume controls.
  1 KB (222 words) - 16:11, 18 April 2023
• T1 to T8S to L1 Model II
  ...er inputs. You will need to control T1 Pan and Level using the T8S PAN/AUX settings. ...er inputs. You will need to control T1 Pan and Level using the T8S PAN/AUX settings.
  2 KB (333 words) - 11:04, 8 April 2019
• LR Baggs Session DI to ToneMatch Mixer T1/T4S/T8S
  ...f your acoustic guitar and the input of a mixer or PA system. With the T4S settings set to FLAT/Bypass follow the instructions in the LR Baggs owner's guide to ==LR Baggs Session DI Settings==
  4 KB (656 words) - 15:13, 3 February 2020
• PorchBoard Floor Bass
  == Settings on the {{L1}} for the PorchBoard == The ToneMatch® settings are
  14 KB (2,215 words) - 14:25, 11 March 2019
• Presets / ToneMatch® / Downloads
  === Original Factory Settings === {{:T1® / Downloads / Factory Settings}}
  7 KB (1,019 words) - 17:46, 2 September 2022
• T1 ToneMatch® Audio Engine / USB / Output Stereo to Two L1®s
  ...}. If you have been following along and have set up our {{T1 nl}} with the settings above, you do not need to download this Shared Scene. I just included this This scene has very generic settings for Channels 1,2 and 3 and the settings discussed in this article for Channel 4/5.
  7 KB (1,115 words) - 16:44, 4 September 2023
• T1 ToneMatch® Audio Engine / Recording / Audacity
  == Audacity Settings == You can record in stereo if you set the project default settings to 48 kHz. If you leave it at the default 44.1 kHz then you can only record
  3 KB (486 words) - 04:54, 26 March 2017
• Larrivee & Morgan ToneMatch Settings
  Cliff Henricksen suggested that I try these settings for my [[Larrivée C10 BZ 30th Anniversary]] and [http://toonz.ca/guitars/m It should be no surprise that these settings work so well for both of these instruments. They are very similar. The body
  1 KB (226 words) - 14:26, 4 November 2019
• Fiddle
  ===Settings for EQ and compression=== EQ settings for the fiddle can vary a bit with each gig. The notch to remove the 'scri
  4 KB (691 words) - 15:30, 22 December 2008
• Larrivée Guitars
  === Settings with {{T1}} === {{:Larrivee & Morgan ToneMatch Settings}}
  3 KB (536 words) - 14:28, 4 November 2019
• Larrivée C10 BZ 30th Anniversary
  === Settings with {{T1}} === {{:Larrivee & Morgan ToneMatch Settings}}
  2 KB (223 words) - 14:28, 4 November 2019
• T1 ToneMatch® Audio Engine / USB / Output Stereo to Two F1 Systems
  ...}. If you have been following along and have set up our {{T1 nl}} with the settings above, you do not need to download this Shared Scene. I just included this This scene has very generic settings for Channels 1,2 and 3 and the settings discussed in this article for Channel 4/5.
  5 KB (809 words) - 17:12, 26 December 2017
• Behringer Xenyx 1002B to S1 Pro System
  == S1 Pro System Settings == {{S1 Pro Mixer Settings}}
  2 KB (443 words) - 22:23, 16 November 2019
• Mackie Pro FX4 to S1 Pro System
  == S1 Pro System Settings == {{S1 Pro Mixer Settings}}
  1 KB (243 words) - 22:25, 16 November 2019
• Set ToneMatch Channel to Factory Settings
  ...y) but if you don't want to lose any saved Scenes you can load the Factory Settings Scene (T1/T4S/T8S). This will set all channels to these settings.
  795 bytes (135 words) - 16:47, 11 January 2020
• T4S to L1 Model 1S
  === T4S Settings === ...single L1 Model II or L1 Model 1S is the RIGHT output. Ensure that the PAN settings for each input are up the center or panned hard right. Any signal panned ha
  511 bytes (94 words) - 01:39, 15 December 2022
• T4S to L1 Model II
  === T4S Settings === ...single L1 Model II or L1 Model 1S is the RIGHT output. Ensure that the PAN settings for each input are up the center or panned hard right. Any signal panned ha
  508 bytes (90 words) - 01:38, 15 December 2022
• L1 System for Volunteer Organization
  ...h mixers can store [[ToneMatch Mixer Scenes|Scene]] (a snapshot of all the settings). You can create a Scene, and others can load them to put the ToneMatch mix # Set up all the connections and settings
  2 KB (300 words) - 16:59, 18 April 2023
• T1 ToneMatch® Audio Engine / USB
  #Factory settings, the default<br>[[Image:T1USBtoPC02a.png|450px]] <noinclude>See: [[{{PAGENAME}}#Settings USB from Computer to Channel 4/5|Settings USB from Computer to Channel 4/5]] (above) for USB setup and [[{{PAGENAME}}
  8 KB (1,290 words) - 18:04, 27 March 2019

View (previous 20 | next 20) (20 | 50 | 100 | 250 | 500)