Difference between revisions of "T1 ToneMatch® Audio Engine / Aux"
(First ed) |
(excerpts from the T1 Manual) |
||
| Line 1: | Line 1: | ||
== Aux Output == | == Aux Output == | ||
| − | The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. | + | The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. Tap points where you can set the output to the Aux. (from page 34 of the {{T1 Manual}} |
| − | + | ||
| − | * | + | * Dry: After Preamp: The completely dry (no processing) signal is routed directly from the preamp stage. |
| − | * Pre | + | * Pre: With EQ & FX: The signal is routed from the preamp stage with applied processing. |
| + | * Post: After Fader: The signal is routed after the Channel volume control with applied processing. | ||
| + | |||
=== No Reverb on Aux === | === No Reverb on Aux === | ||
| Line 15: | Line 17: | ||
The discussion continues in the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/4091082864?r=8551095774#8551095774 Message Board] | The discussion continues in the [http://bose.infopop.cc/eve/forums/a/tpc/f/7521050644/m/4091082864?r=8551095774#8551095774 Message Board] | ||
| − | + | Reference: page 52 of the {{T1 Manual}} | |
| − | |||
Problem: Aux output does not sound right. | Problem: Aux output does not sound right. | ||
Revision as of 21:39, 29 July 2007
Aux Output
The output of any of the Channels 1, 2, 3, 4/5 can be sent to the Aux out. Tap points where you can set the output to the Aux. (from page 34 of the T1 ToneMatch® Audio Engine Owner's Guide (62 pages)
- Dry: After Preamp: The completely dry (no processing) signal is routed directly from the preamp stage.
- Pre: With EQ & FX: The signal is routed from the preamp stage with applied processing.
- Post: After Fader: The signal is routed after the Channel volume control with applied processing.
No Reverb on Aux
Q: Why is there no Reverb on the Aux output of the T1 ToneMatch Audio Engine?
A: Hilmar-at-Bose writes[1]
- The T1 ToneMatch Audio Engine has lots of different effects units and normally they are unique to each channel. That means that the T1™ has 4 individual dynamic processors, 4 modulators (chorus flanger, phaser, etc.) , 4 EQs, 4 delay processors, etc. The only exception is the reverb, which is shared by all channels.
- The AUX is also a per-channel control. That means if you turn up the AUX of channel, you expect to hear signals from channel 1 and only from channel 1. However, the output of the reverb processor contains the reverb portions of all 4 channels. If we add that to the Aux, you'd hear the reverb portions of all 4 channels and not only the channel that you are interested in. In most cases, this is probably not what you want.
- If you are familiar with conventional mixing consoles, you will find that the situation is quite similar. You can only route to an AUX output effects that are specific to a channel (normally these would be connected to the insert loop of this channel). The "shared" effects typically come into the board through an AUX return, which is not channel specific.
The discussion continues in the Message Board
Reference: page 52 of the T1 ToneMatch® Audio Engine Owner's Guide (62 pages)
Problem: Aux output does not sound right.
What To Do:
- Check if the Aux output is configured for the desired tap point for each input channel. Refer to “Routing input
signals to the Aux output” on page 26.
Note: No reverb comes from the Aux output even if the tap point is Pre or Post.
- Verify that each input assigns the desired signal level to the Aux output.
- ↑ Hilmar-at-Bose writes about No Reverb on Aux