Template:Kemper Profiler to Bose Portable PA

From Bose Portable PA Encyclopedia
Jump to: navigation, search

ToneMatch Mixer

T4S This information is applicable to the T4S ToneMatch® mixer
T8S This information is applicable to the T8S ToneMatch® mixer
T1 This information is applicable to the T1 ToneMatch® audio engine

Set everything flat on the ToneMatch mixer and control the guitar sound on the Profiler. If necessary, use the zEQ or ParaEQ to solve acoustic issues at the venue. That is: Use the Profiler to create your guitar sound. If necessary, use the zEQ and ParaEQ on the ToneMatch to deal with the environment. That way, when you move to a different environment, you don't have to make changes to the Profiler.

Connections

Connect the Profiler Main Output to the ToneMatch mixer (since the ToneMatch mixer is the input to the FOH (Front of House)).

  • XLR connection. This is a balanced connection and it is preferable
  • 1/4 inch (6.35 mm) Tip-Sleeve (Ordinary guitar cable). Avoid using this connection when you have cable runs in excess of 20 feet (six meters).
    There is no advantage to using a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable because the 1/4 inch (6.35 mm) Profiler outputs are unbalanced.
Profiler Main Outputs
These are your main stereo outputs. Use these outputs to connect to a mixing desk in a recording studio, or to the front-of-house mixer in a live situation. These outputs deliver the entire Rig: amp, cabinet, and all effects. You have a choice of XLR (balanced) or quarter-inch TS-jacks (unbalanced). The XLR outputs are protected against 48V phantom power fed by a mixing desk. However, you should avoid feeding phantom power into the PROFILER if you want the best audio quality. Like all inputs and outputs, it offers a ground lift to prevent a loop hum.

Source: Kemper Main Manual


Settings

In the Profile Output section, page 1, Set Main Output to Master Mono (or Master Stereo if you are running two L1 systems).

On the ToneMatch mixer, on the channel to which you have attached the Profiler

ToneMatch Preset
Category: Electric Guitars
Preset: Flat E. Guitar ZEQ or General Processor [try both]
ZEQ
Lo, Mid, Hi set to 0 (I use this for quick changes to compensate for room acoustics)
ParaEQ
All bypassed
Comp/Gate
Bypassed
Mod
Bypassed
Delay
Bypassed
Reverb
Bypassed

No Mixer

If you are not using a mixer between the Profiler and the Bose system, this section is for you.

L1 Pro

L1 Pro This information is applicable to the L1 Pro

You can connect the Profile Main Output to the L1 Pro Input 3.

Connections
  • XLR connection. This is a balanced connection and it is preferable
  • 1/4 inch (6.35 mm) Tip-Sleeve (Ordinary guitar cable). Avoid using this connection when you have cable runs in excess of 20 feet (six meters).
    There is no advantage to using a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable because the 1/4 inch (6.35 mm) Profiler outputs are unbalanced.
Profiler Main Outputs
These are your main stereo outputs. Use these outputs to connect to a mixing desk in a recording studio, or to the front-of-house mixer in a live situation. These outputs deliver the entire Rig: amp, cabinet, and all effects. You have a choice of XLR (balanced) or quarter-inch TS-jacks (unbalanced). The XLR outputs are protected against 48V phantom power fed by a mixing desk. However, you should avoid feeding phantom power into the PROFILER if you want the best audio quality. Like all inputs and outputs, it offers a ground lift to prevent a loop hum.

Source: Kemper Main Manual


L1 Model 1S/L1 Model II

L1 Model II This information is applicable to the L1®  Model II
L1 Model 1S This information is applicable to the L1®  Model 1S

Connect the Profiler Main Output to the Analog Input on the Power Stand. Set the Analog Input Trim so you get a solid green light. If you see solid red, turn down the Trim

L1 Compact

L1 Compact

Connect the Profiler Main Output to Channel 2. Set the ToneMatch switch to Line Level (Down).

S1 Pro

S1 Pro  This information is applicable to the S1 Pro system

Connect the Profiler Main Output to Channel 1 or 2.

Connections
  • XLR connection. This is a balanced connection and it is preferable
  • 1/4 inch (6.35 mm) Tip-Sleeve (Ordinary guitar cable). Avoid using this connection when you have cable runs in excess of 20 feet (six meters).
    There is no advantage to using a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable because the 1/4 inch (6.35 mm) Profiler outputs are unbalanced.
Profiler Main Outputs
These are your main stereo outputs. Use these outputs to connect to a mixing desk in a recording studio, or to the front-of-house mixer in a live situation. These outputs deliver the entire Rig: amp, cabinet, and all effects. You have a choice of XLR (balanced) or quarter-inch TS-jacks (unbalanced). The XLR outputs are protected against 48V phantom power fed by a mixing desk. However, you should avoid feeding phantom power into the PROFILER if you want the best audio quality. Like all inputs and outputs, it offers a ground lift to prevent a loop hum.

Source: Kemper Main Manual


Another option is to connect the Profiler headphone output to the S1 Pro Input 3 (the 1/8 inch (3mm) input). Input 3 is stereo.

F1 Model 812

F1 Model 812This information is applicable to the F1 Flexible Array Loudspeaker

Connect the Profiler Main Output to Channel 1 or 2.

Connections
  • XLR connection. This is a balanced connection and it is preferable
  • 1/4 inch (6.35 mm) Tip-Sleeve (Ordinary guitar cable). Avoid using this connection when you have cable runs in excess of 20 feet (six meters).
    There is no advantage to using a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable because the 1/4 inch (6.35 mm) Profiler outputs are unbalanced.
Profiler Main Outputs
These are your main stereo outputs. Use these outputs to connect to a mixing desk in a recording studio, or to the front-of-house mixer in a live situation. These outputs deliver the entire Rig: amp, cabinet, and all effects. You have a choice of XLR (balanced) or quarter-inch TS-jacks (unbalanced). The XLR outputs are protected against 48V phantom power fed by a mixing desk. However, you should avoid feeding phantom power into the PROFILER if you want the best audio quality. Like all inputs and outputs, it offers a ground lift to prevent a loop hum.

Source: Kemper Main Manual