Difference between revisions of "Mixer / Mackie / 1202-VLZ"
m (* [http://mackie.com/pdf/1202vlzpro_om.pdf Mackie 1202-VLZ Manual]) |
m |
||
| (10 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | {{Classic icon}}{{Model I icon}} | |
== Summary == | == Summary == | ||
| Line 9: | Line 9: | ||
Use the '''XLR''' - or - '''¼ inch phone jack''' (Tip-Sleeve) outputs to | Use the '''XLR''' - or - '''¼ inch phone jack''' (Tip-Sleeve) outputs to | ||
| − | * The {{PS1}} Channels 1 or 2 if you want to use the [[Presets]] and the [[R1 Remote]] Tone and Level Controls | + | * The {{PS1}} Channels 1 or 2 if you want to use the [[Presets/Model I and Classic|Presets]] and the [[R1 Remote]] Tone and Level Controls |
<br /> OR <br /> | <br /> OR <br /> | ||
* The {{PS1}} Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the {{PS1}} or the [[R1 Remote]]. | * The {{PS1}} Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the {{PS1}} or the [[R1 Remote]]. | ||
| Line 22: | Line 22: | ||
Links: | Links: | ||
| − | * [http://mackie.com/pdf/1202vlzpro_om.pdf Mackie 1202-VLZ Manual] | + | * [http://mackie.com/pdf/1202vlzpro_om.pdf Mackie 1202-VLZ Pro Manual] |
| + | === Notes about MIC/Line Switch === | ||
| + | When using an XLR cable between the mixer and the Model I or Classic Power Stand, set the mixer Master Output Switch to '''MIC''' because the Model I / Classic Channel 1/2 XLR Inputs are designed to accept a '''Microphone level input'''. | ||
| + | [[Image:ModelIChannel1InputXLRisMIC.jpg]] | ||
| + | |||
| + | |||
| + | ;The mixer allows you to match that requirement by using the MIC setting. | ||
| + | |||
| + | [[Image:Mackie1202OutputSwitch.jpg]] | ||
| + | |||
| + | Details of the MIC/Line Switch from pages 15 and 26 of the [http://mackie.com/pdf/1202vlzpro_om.pdf Mackie 1202-VLZ Pro Manual] | ||
| + | |||
| + | [[Image:Mackie1202VLZProOutputDiagram.jpg]] | ||
Latest revision as of 11:28, 18 March 2012
Contents
Summary
You can use either the XLR outputs on the rear panel (be sure to set the MIC button "in")
- - or -
Use the ¼ inch phone jacks on the top.
Use the XLR - or - ¼ inch phone jack (Tip-Sleeve) outputs to
- The PS1 Power Stand (Classic) / Model I Channels 1 or 2 if you want to use the Presets and the R1 Remote Tone and Level Controls
OR
- The PS1 Power Stand (Classic) / Model I Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the PS1 Power Stand (Classic) / Model I or the R1 Remote.
- If you want to use the Balanced XLR outputs use the MIC setting in the picture above.
¼ Inch with suitable output
for PS1 Powerstand Channel 1 or 2 inputs
You can use TS (Tip Sleeve) unbalanced cables, or TRS (Tip Ring Sleeve) balanced cables, but since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.
Links:
Notes about MIC/Line Switch
When using an XLR cable between the mixer and the Model I or Classic Power Stand, set the mixer Master Output Switch to MIC because the Model I / Classic Channel 1/2 XLR Inputs are designed to accept a Microphone level input.
- The mixer allows you to match that requirement by using the MIC setting.
Details of the MIC/Line Switch from pages 15 and 26 of the Mackie 1202-VLZ Pro Manual
