Difference between revisions of "Mixer / Behringer / UB1222FX-Pro"
m (Mixer/Behringer/UBX 1222FX moved to Mixer/Behringer/UB1222FX-Pro: corrected model number) |
m (emphasized using Mon Out for ¼ inch outputs.) |
||
| Line 9: | Line 9: | ||
== Summary == | == Summary == | ||
| − | Simplest thing that could possibly work. | + | Simplest thing that could possibly work. |
''' {{Use1/4}} ''' | ''' {{Use1/4}} ''' | ||
| − | If you are running one L1™ you can try using the Mon Out. This is ¼ inch Tip-Sleeve that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs. | + | If you are running one L1™ you can try using the '''Mon Out'''. This is ¼ inch Tip-Sleeve that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs. |
== Outputs == | == Outputs == | ||
| Line 23: | Line 23: | ||
=== ¼ Inch with suitable output=== | === ¼ Inch with suitable output=== | ||
| − | + | Mixer '''Mon Out''' to the PS1 Powerstand Channel 1 or 2 inputs | |
{{RunTROrTRSUnbalanced}} | {{RunTROrTRSUnbalanced}} | ||
Revision as of 22:07, 13 August 2007
Behringer UBX 1222FX Mixer
Contents
Summary
Simplest thing that could possibly work.
Use the ¼ inch phone jack (Tip-Sleeve) outputs to
- The PS1 Power Stand (Classic) / Model I Channels 1 or 2 if you want to use the Presets and the R1 Remote Tone and Level Controls
OR - The PS1 Power Stand (Classic) / Model I Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the PS1 Power Stand (Classic) / Model I or the R1 Remote.
If you are running one L1™ you can try using the Mon Out. This is ¼ inch Tip-Sleeve that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs.
Outputs
XLR Balanced +4
The nominal output of the XLR Balanced Outputs is too high for the XLR inputs on the PS1 Power Stand Channels 1 and 2. If you want to use balanced cables from the Mixer to Channels 1/2 on the L1 Classic or L1 Model I you may need to use a Pad to lower the signal level from the mixer.
{{#Click:Pad|Image:Pad.jpg|Attenuation Pad}}
¼ Inch with suitable output
Mixer Mon Out to the PS1 Powerstand Channel 1 or 2 inputs
You can use TS (Tip Sleeve) unbalanced cables, or TRS (Tip Ring Sleeve) balanced cables, but since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.
Links:
