Difference between revisions of "Mixer / Yamaha / MX12/4"
(image links and detail in the final links section.) |
m (Mixer / Yamaha / MX12 / 4 moved to Mixer / Yamaha / MX12/4: nc) |
||
| (6 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| − | + | {{Classic icon}}{{Model I icon}} | |
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
| − | |||
<big>''' Yamaha MX12/4 '''</big> | <big>''' Yamaha MX12/4 '''</big> | ||
| Line 21: | Line 15: | ||
== Outputs == | == Outputs == | ||
<!-- delete anything that is not applicable --> | <!-- delete anything that is not applicable --> | ||
| − | |||
| − | |||
<!-- | <!-- | ||
=== XLR Balanced with built-in-pad === | === XLR Balanced with built-in-pad === | ||
| Line 32: | Line 24: | ||
for PS1 Powerstand Channel 1 or 2 inputs | for PS1 Powerstand Channel 1 or 2 inputs | ||
| − | The ¼ inch Console should work fine directly into the {{PS1}} Channels 1/2/3/4. Note: this output is [[TRS|Tip-Ring-Sleeve]] (stereo output) so you will need a Tip-Ring-Sleeve to two Tip-Sleeve patch cord to maintain the separation of the left and right channels. | + | The ¼ inch Console |
| + | * Page 6 in the Manual showing outputs. #7 highlighted is the Stereo Console out. <br />[[Image:YamahaMX124Out1.gif]] | ||
| + | |||
| + | should work fine directly into the {{PS1}} Channels 1/2/3/4. Note: this output is [[TRS|Tip-Ring-Sleeve]] (stereo output) so you will need a Tip-Ring-Sleeve to two Tip-Sleeve patch cord to maintain the separation of the left and right channels. <br />[[Image:InsertCable.gif]] | ||
| + | |||
| + | This Mixer also has Four group outputs (busses). Note that the 'sends' are pre-fader. | ||
| − | + | * Page 6 in the Manual showing outputs. #6 highlighted are the ¼ inch group outputs. <br />[[Image:YamahaMX124Out2.gif]] | |
{{RunTROrTRSUnbalanced}} | {{RunTROrTRSUnbalanced}} | ||
| + | |||
| + | === XLR Balanced +4 === | ||
| + | |||
| + | {{TooHotForPS1}} | ||
| + | |||
| + | * Page 6 in the Manual showing outputs. #5 highlighted are the [[XLR]] balanced outputs. These output +4 dBU nominal and are likely too hot for direct input to the [[XLR]] inputs on the {{PS1}}. Use [[Pad]]s.<br />[[Image:YamahaMX124Out3.gif]] | ||
Links: | Links: | ||
* [http://www2.yamaha.co.jp/manual/pdf/pa/english/mixers/MX12_4E.pdf Yamaha MX12/4 Manual] | * [http://www2.yamaha.co.jp/manual/pdf/pa/english/mixers/MX12_4E.pdf Yamaha MX12/4 Manual] | ||
| − | + | ||
| − | + | ||
| − | |||
More Notes | More Notes | ||
| − | + | Reading the manual it is not clear (to me) if you can use the internal effects while routing outputs through the groups 1-4. | |
| Line 54: | Line 56: | ||
<references/> | <references/> | ||
| − | [[ | + | [[Category:Mixer]] |
| + | [[Category:Yamaha]] | ||
Latest revision as of 02:20, 21 December 2008
Yamaha MX12/4
Contents
Summary
Simplest thing that could possibly work.
Use the ¼ inch phone jack (Tip-Sleeve) outputs to
- The PS1 Power Stand (Classic) / Model I Channels 1 or 2 if you want to use the Presets and the R1 Remote Tone and Level Controls
OR - The PS1 Power Stand (Classic) / Model I Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the PS1 Power Stand (Classic) / Model I or the R1 Remote.
or
You can use the XLR Balanced outputs. But you will probably want to use a Pad for each channel.
Outputs
¼ Inch with suitable output
for PS1 Powerstand Channel 1 or 2 inputs
The ¼ inch Console
- Page 6 in the Manual showing outputs. #7 highlighted is the Stereo Console out.
should work fine directly into the PS1 Power Stand (Classic) / Model I Channels 1/2/3/4. Note: this output is Tip-Ring-Sleeve (stereo output) so you will need a Tip-Ring-Sleeve to two Tip-Sleeve patch cord to maintain the separation of the left and right channels. 
This Mixer also has Four group outputs (busses). Note that the 'sends' are pre-fader.
- Page 6 in the Manual showing outputs. #6 highlighted are the ¼ inch group outputs.
You can use TS (Tip Sleeve) unbalanced cables, or TRS (Tip Ring Sleeve) balanced cables, but since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.
XLR Balanced +4
The nominal output of the XLR Balanced Outputs is too high for the XLR inputs on the PS1 Power Stand Channels 1 and 2. If you want to use balanced cables from the Mixer to Channels 1/2 on the L1 Classic or L1 Model I you may need to use a Pad to lower the signal level from the mixer.
{{#Click:Pad|Image:Pad.jpg|Attenuation Pad}}
- Page 6 in the Manual showing outputs. #5 highlighted are the XLR balanced outputs. These output +4 dBU nominal and are likely too hot for direct input to the XLR inputs on the PS1 Power Stand (Classic) / Model I. Use Pads.
Links:
More Notes
Reading the manual it is not clear (to me) if you can use the internal effects while routing outputs through the groups 1-4.