Difference between revisions of "Mixer / Behringer / UB1202FX"
(first ed) |
m (→Summary: formatting) |
||
| (7 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | {{Classic icon}}{{Model I icon}} | ||
<big>''' Behringer UBX 1202FX Mixer'''</big> | <big>''' Behringer UBX 1202FX Mixer'''</big> | ||
== Summary == | == Summary == | ||
| − | [[Image:BehringerUB1202FXOutput.png] | + | Use unbalanced ¼ inch Tip-Sleeve phone jack cables from the Mixer to the {{PS1}}. |
| + | |||
| + | [[Image:BehringerUB1202FXOutputSpecific.png]] | ||
| + | <!-- | ||
| + | [[Image:BehringerUB1202FXOutput.png]] | ||
| + | --> | ||
''' {{Use1/4}} ''' | ''' {{Use1/4}} ''' | ||
The main outputs from this mixer are unbalanced ¼ inch Tip-Sleeve phone jacks that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs. | The main outputs from this mixer are unbalanced ¼ inch Tip-Sleeve phone jacks that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs. | ||
| − | |||
== Outputs == | == Outputs == | ||
| Line 18: | Line 23: | ||
Links: | Links: | ||
| − | * [http://www.behringerdownload.de/UB1002FX_UB1202FX/UB1002FX_UB1202FX_ENG_Rev_A. | + | * [http://www.behringerdownload.de/UB1002FX_UB1202FX/UB1002FX_UB1202FX_ENG_Rev_A.pdf Behringer Eurorack UB1202FX Manual] |
| + | Note: the UB1002FX and UB1202FX share the same manual. | ||
| + | [[Image:BehringerUB1002-UB1202FX.png]] | ||
Latest revision as of 10:09, 11 September 2009
Behringer UBX 1202FX Mixer
Contents
Summary
Use unbalanced ¼ inch Tip-Sleeve phone jack cables from the Mixer to the PS1 Power Stand (Classic) / Model I.
Use the ¼ inch phone jack (Tip-Sleeve) outputs to
- The PS1 Power Stand (Classic) / Model I Channels 1 or 2 if you want to use the Presets and the R1 Remote Tone and Level Controls
OR - The PS1 Power Stand (Classic) / Model I Channels 3 or 4 if you prefer to leave Channels 1 or 2 open for other inputs. You will have to control Tone and relative Level (between the Channels) at your input source, as you do not have this control over Channels 3 and 4 in the PS1 Power Stand (Classic) / Model I or the R1 Remote.
The main outputs from this mixer are unbalanced ¼ inch Tip-Sleeve phone jacks that you can run to the Channel 1 or 2 ¼ inch Tip-Sleeve inputs.
Outputs
¼ Inch with suitable output
for PS1 Powerstand Channel 1 or 2 inputs
You can use TS (Tip Sleeve) unbalanced cables, or TRS (Tip Ring Sleeve) balanced cables, but since the ¼ inch phone connections at the Bose Classic and Model I Power Stand are unbalanced there is no particular benefit using balanced cables.
¼ Inch Tip-Sleeve (unbalanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Sleeve (unbalanced)
This should work fine.
¼ Inch Tip-Ring-Sleeve (balanced) to ¼ Inch Tip-Ring-Sleeve (balanced)
This should also work, but likely no better than a simple ¼ Inch Tip-Sleeve to Tip-Sleeve cable. This is because the ¼ Inch input on the Bose System is Tip-Sleeve (unbalanced) anyway.
Links:
Note: the UB1002FX and UB1202FX share the same manual.
