Difference between revisions of "S1 Pro as Monitor with Third Party Mixer and L1"
m |
m |
||
Line 1: | Line 1: | ||
{{Model II}}{{S1 icon}} | {{Model II}}{{S1 icon}} | ||
+ | <div class="tocdiv"> | ||
+ | <div>__TOC__</div> | ||
+ | <div><h2>Summary</h2> | ||
+ | This is an overview of how you can connect a third party mixer to an L1 as the main output and {{S1}} as a monitor. | ||
+ | </div> | ||
− | == | + | == Example == |
− | + | You can connect using the XLR outputs from a mixer. | |
+ | |||
+ | This assumes you are running mono and have all mixer inputs panned up the middle. | ||
[[File:Yamaha MG10XU L1 S1 XLR.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 XLR.jpg|400px]] | ||
+ | |||
+ | You can connect using the {{1/4 TRS}} outputs from a mixer. | ||
[[File:Yamaha MG10XU L1 S1 TRS.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 TRS.jpg|400px]] | ||
+ | |||
+ | If your mixer has both XLR and {{1/4 TRS}} outputs, you can pan all inputs to one side (e.g., Left) and connect like this. | ||
[[File:Yamaha MG10XU L1 S1 14 XLR trs.jpg|400px]] | [[File:Yamaha MG10XU L1 S1 14 XLR trs.jpg|400px]] | ||
+ | |||
+ | Set the controls on the {{S1}} like this. | ||
[[File:S1 Pro Settings for mixer.jpg|250px|S1 Pro inputs]] | [[File:S1 Pro Settings for mixer.jpg|250px|S1 Pro inputs]] |
Revision as of 14:07, 9 April 2019
Summary
This is an overview of how you can connect a third party mixer to an L1 as the main output and S1 Pro System as a monitor.
Example
You can connect using the XLR outputs from a mixer.
This assumes you are running mono and have all mixer inputs panned up the middle.
You can connect using the 1/4 inch (6.35 mm) Tip-Ring-Sleeve outputs from a mixer.
If your mixer has both XLR and 1/4 inch (6.35 mm) Tip-Ring-Sleeve outputs, you can pan all inputs to one side (e.g., Left) and connect like this.
Set the controls on the S1 Pro System like this.
Cables
- The T1 ToneMatch Audio Engine Analog Outputs and the S1 Pro System 1/4 inch (6.3 mm) inputs are balanced. For best results use a 1/4 inch (6.35 mm) Tip-Ring-Sleeve cable for a balanced connection. You can use a 1/4 inch (6.35 mm) Tip-Sleeve , but you will lose up to -6 dB in signal strength and you may pick up line noise.
S1 Pro System settings
On the S1 Pro System use these settings while you are setting up.
- Reverb OFF
- Bass at 12:00 o'clock
- Treble at 12:00 o'clock
- ToneMatch switch OFF
You can adjust the Reverb, Bass, and Treble after you get your basic sound working.
S1 Pro System Gain Staging
For each channel you are using on the S1 Pro System,
- Turn the channel volume off
- Connect the T1 ToneMatch Audio Engine Master Output of T1 ToneMatch Audio Engine Aux Output
- Set the T1 ToneMatch Audio Engine to the maximum you will use during your performance.
- While playing/singing as loud as you will during your performance, bring up the S1 Pro System channel volume until you see solid green on the channel indicator light. Occasional flickers of red are okay. If you see solid red or you hear distortion, turn down the volume.