Difference between revisions of "Bass Line Out"

From Bose Portable PA Encyclopedia
Jump to: navigation, search
m
m
 
(2 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
<table cellpadding="10"><tr>
 
<table cellpadding="10"><tr>
<td valign="top" width="250">__TOC__</td>
+
<td valign="top" width="400">__TOC__</td>
 
<td valign="top">
 
<td valign="top">
 
The Power Stand for the {{Classic}}, {{Model I}} and {{Model II}} have a balanced &frac14; inch jack line out for bass expansion. See the links below for details.
 
The Power Stand for the {{Classic}}, {{Model I}} and {{Model II}} have a balanced &frac14; inch jack line out for bass expansion. See the links below for details.
Line 6: Line 6:
 
[[PS1 Power Stand / Bass Line Out|L1 Model I / Classic Power Stand / Bass Line Out]]
 
[[PS1 Power Stand / Bass Line Out|L1 Model I / Classic Power Stand / Bass Line Out]]
  
{{#Click:PS1 Power Stand / Bass Line Out|Image:ModelIBassOutputs.png|200px|Model I / Classic}}
+
[[File:ModelIBassOutputs.png|link=PS1 Power Stand / Bass Line Out|300px|Model I / Classic]]
 +
<!--
 +
{{#Click:PS1 Power Stand / Bass Line Out|Image:ModelIBassOutputs.png|300px|Model I / Classic}}
 +
-->
  
 
[[L1® Model II Power Stand / Bass Line Out]]
 
[[L1® Model II Power Stand / Bass Line Out]]
  
{{#Click:L1® Model II Power Stand / Bass Line Out|Image:ModelIIBassOutputs.png|200px|Model II}}
+
[[File:ModelIIBassOutputs.png|link=L1® Model II Power Stand / Bass Line Out|300px|Model II]]
 +
 
 +
<!--
 +
{{#Click:L1® Model II Power Stand / Bass Line Out|Image:ModelIIBassOutputs.png|300px|Model II}}
 +
 
 +
-->
 
</td>
 
</td>
 
</tr></table>   
 
</tr></table>   
 
The Power Stand for the {{Classic}}, {{Model I}} and {{Model II}} have a balanced &frac14; inch jack line out for bass expansion. See the links below for details.
 
 
[[PS1 Power Stand / Bass Line Out|L1 Model I / Classic Power Stand / Bass Line Out]]
 
 
{{#Click:PS1 Power Stand / Bass Line Out|Image:ModelIBassOutputs.png|400px|Model I / Classic}}
 
 
[[L1® Model II Power Stand / Bass Line Out]]
 
 
{{#Click:L1® Model II Power Stand / Bass Line Out|Image:ModelIIBassOutputs.png||Model II}}
 
  
 
= Model I / Classic =
 
= Model I / Classic =

Latest revision as of 13:49, 28 May 2019

The Power Stand for the L1 Classic, L1 Model I and L1 Model II have a balanced ¼ inch jack line out for bass expansion. See the links below for details.

L1 Model I / Classic Power Stand / Bass Line Out

Model I / Classic

L1® Model II Power Stand / Bass Line Out

Model II

Model I / Classic

This Page Reviewed By Bose



Bass Line Out and B1 behavior

Model I right side Input/Output panel


The behavior of the bass line out and B1 Bass Module outputs on the L1 Classic / L1 Model I / L1 Model II are based on the philosophy that adding B1 Bass Modules should give the user more dynamic range (can play louder) but should not alter the tone of the instrument, including tone adjustments made using the R1 Remote, the T1 ToneMatch Audio Engine or other tone-shaping equipment.

This philosophy is notably different from other manufacturers, who take the approach that it's okay (or desirable) that adding more bass speakers causes the instrument tone to become "bassier".

With this philosophy in mind, here is how the bass line out and B1 outputs work.

No cable plugged into the Bass Line out

B1s connected OutputEQ Bass Signal Gain Notes
1 40Hz-180Hz B1 specific EQ Reference Level
2 40Hz-180Hz B1 specific EQ Reference Level -6 dB Why? Because when you add a second B1, if you did not change the signal strength you would get 6 dB more bass relative to the mids and highs. This would alter the tone of the instrument. To keep the tone the same, while still allowing the more dynamic range (system can play louder by 6 dB) the signal level must be reduced by 6 dB.


Cable connected to the Bass Line Out

B1s connected OutputEQ Bass Signal Gain Notes
0 40Hz-180Hz Flat EQ Reference Level -6 dB
1 40Hz-180Hz B1 specific EQ on Bass Line Out and B1 Out Reference Level - 6 dB If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of 3 B1s (2 on the A1 and 1 on the Power Stand)
2 40Hz-180Hz B1 specific EQ on Bass Line Out and B1 Out Reference Level -12 dB If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of 4 B1s (2 on the A1 and 2 on the Power Stand)

With More Than 4 B1s

The Power Stand does not measure the exact number of PackLite® power amplifier model A1s, so there is a slight error if you use anything but 1,2, or 4 B1s.

For 6 B1s you will be 3.5 dB bass heavy, for 8 B1s it'll be 6 dB heavy.

B2 EQ

Bass Line Out: Model II post firmware 1.4 with System EQ 1.04

Model II Bass OutputsB2 Bass Level Switch


September 2012

Bose released Model II Power Stand Model II firmware 1.4 with System EQ 1.04 to support the B2 Bass Module with the three position Bass Level Switch ( + Normal - ). Note: Support and behaviors for B1(s) is unchanged.
The behavior of the bass line out with the B2 Bass Module Bass Module outputs on the Model 1S and Model II are based on the philosophy that adding B2 Bass Modules should give the user more bass output immediately. This changes the tonal balance as soon as you add a second B2 using an PackLite® power amplifier model A1 connected to the Bass Line Out. This is unlike the behaviour with B1 bass modules where the signal is attenuated as you add more B1s to maintain the tonal balance at lower volume levels.
Note: If no bass modules are detected at the Bass Module Output the Bass Line Out EQ will be set to the B2 curve with the B2 switch set to Normal.
— Source Craig-at-Bose

No cable plugged into the Bass Line out

B2 Bass Modules connected Output EQ Bass Signal Gain Notes
1 40Hz-200Hz B2 specific EQ as set by the B2 Bass Level Switch ( + Normal - ) is present at the Bass Module Out and the Bass Line Out Reference Level There are three B2 EQ settings possible using the B2 Bass Level Switch ( + Normal - )

Cable connected to the Bass Line Out

B2 Bass Modules connected Output EQ Bass Signal Gain Notes
0 40Hz-200Hz B2 EQ as though B2 attached and B2 Bass Level Switch set to Normal position Reference Level This presents the B2 EQ with the B2 Bass Level Switch set to the Normal position. (No resistance detected between the 2+ and 2- pins of an NL4 plug)
1 40Hz-200Hz B2 specific EQ as set by the B2 Bass Level Switch ( + Normal - )
is present at the Bass Module Out and the Bass Line Out
Reference Level If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of two B2s (one on the A1 and one on the Power Stand)

Powered Subwoofers

The Model II is an integrated system that supports Bose B1 and B2 bass modules. Connecting powered subwoofers to the Model II Power Stand Bass Line Out is not supported because EQ curves for the B1 or B2 are present at the Bass Line Out. This may or may not result in good results with a powered subwoofer.

If you want to use a powered subwoofer, connect your signal source to the subwoofer and connect the subwoofer high pass filter output to the L1® (any model).

Output if no B1 Bass Modules detected at the Bass Module Output (powered output) the signal at the Bass Line Out is:

  • 40-180 Hz with B2 EQ applied if you have the current L1® Model II Power Stand Firmware Updates
    • If you do not have the current firmware the signal at the Bass Line Out is: 40-180 Hz Bandpass (that is: NO B1 EQ) [1]
  • The system Crossover for the Cylindrical Radiator®s is 180 Hz

If one or two B1 Bass Modules is detected or emulated using resistors across NL4 2+ / 2- pins

  • 40-180 Hz with different EQ curves
  • The system Crossover for the Cylindrical Radiator®s is 180 Hz

For details on how to do this see: Activating B1 EQ Curves and Using a Different Sub


Note — Operation of the B2 with the Model I/Classic is only supported with the B2 Bass Level Switch set to Normal.
See: Is the B2 Bass Module Compatible with the L1® Classic or Model I


Bass Module Output (powered output)

For the sake of those attaching third party passive speakers (an unsupported application), the output characteristics are the same as for the the B2 Bass Module (section immediately above).



  1. Hilmar-at-Bose intelligent crossover
    A) When there are no bass sources attached, lower the crossover and try to get as much bass out of the L1 as is reasonably feasible (110 Hz) in this case
    B) If there are bass sources bring the crossover up to 180 Hz (where the L1 starts to get really efficient) AND adjust the bass gain so that the overall spectral balance is maintained no matter how many bass sources are attached.


Original Source - Hilmar-at-Bose




Use the proper cables

Warning - Use Blue B1 Cables NL4 cables with your L1 Classic / L1 Model I / L1 Model 1S L1 Model II

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I
L1 Model II This information is applicable to the L1®  Model II
B1 Bass ModuleThis information is applicable to the B1 Bass Module
B2 Bass ModuleThis information is applicable to the B2 Bass Module

If you are using a B1 Bass Module with your Power Stand it is ESSENTIAL for proper operation that you use the BLUE cable supplied with the B1 Bass Module or B2 Bass Module. This is required so that the L1 Classic/L1 Model I/L1 Model 1S/L1 Model II Power Stand can correctly identify when there are bass modules connected to it and if so, how many.

B1 Cable


Please click the picture above for ordering information.

Note
The B2 Bass Level Switch will not change the sound of the B2 Bass Module if you are not using the correct cable.

See: PS1 Power Stand / Bass Line Out for details about how the Power Stand adapts to the number of bass modules are connected to it.


You may also use high quality NL4 cables (four conductor cables). Alternate and longer cables for B1s




Model II



Bass Line Out and B1 behavior

Model II Bass Outputs


The behavior of the bass line out and B1 Bass Module outputs on the L1 Classic / L1 Model I / L1 Model II are based on the philosophy that adding B1 Bass Modules should give the user more dynamic range (can play louder) but should not alter the tone of the instrument, including tone adjustments made using the R1 Remote, the T1 ToneMatch Audio Engine or other tone-shaping equipment.

This philosophy is notably different from other manufacturers, who take the approach that it's okay (or desirable) that adding more bass speakers causes the instrument tone to become "bassier".

With this philosophy in mind, here is how the bass line out and B1 outputs work.

No cable plugged into the Bass Line out

B1s connected OutputEQ Bass Signal Gain Notes
1 40Hz-200Hz B1 specific EQ Reference Level
2 40Hz-200Hz B1 specific EQ Reference Level -6 dB Why? Because when you add a second B1, if you did not change the signal strength you would get 6 dB more bass relative to the mids and highs. This would alter the tone of the instrument. To keep the tone the same, while still allowing the more dynamic range (system can play louder by 6 dB) the signal level must be reduced by 6 dB.


Cable connected to the Bass Line Out

B1s connected OutputEQ Bass Signal Gain Notes
0 40Hz-200Hz Flat EQ Reference Level -6 dB
1 40Hz-200Hz B1 specific EQ on Bass Line Out and B1 Out Reference Level - 6 dB If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of 3 B1s (2 on the A1 and 1 on the Power Stand)
2 40Hz-200Hz B1 specific EQ on Bass Line Out and B1 Out Reference Level -12 dB If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of 4 B1s (2 on the A1 and 2 on the Power Stand)

With More Than 4 B1s

The Power Stand does not measure the exact number of PackLite® power amplifier model A1s, so there is a slight error if you use anything but 1,2, or 4 B1s.

For 6 B1s you will be 3.5 dB bass heavy, for 8 B1s it'll be 6 dB heavy.

B2 EQ

Bass Line Out: Model II post firmware 1.4 with System EQ 1.04

Model II Bass OutputsB2 Bass Level Switch


September 2012

Bose released Model II Power Stand Model II firmware 1.4 with System EQ 1.04 to support the B2 Bass Module with the three position Bass Level Switch ( + Normal - ). Note: Support and behaviors for B1(s) is unchanged.
The behavior of the bass line out with the B2 Bass Module Bass Module outputs on the Model 1S and Model II are based on the philosophy that adding B2 Bass Modules should give the user more bass output immediately. This changes the tonal balance as soon as you add a second B2 using an PackLite® power amplifier model A1 connected to the Bass Line Out. This is unlike the behaviour with B1 bass modules where the signal is attenuated as you add more B1s to maintain the tonal balance at lower volume levels.
Note: If no bass modules are detected at the Bass Module Output the Bass Line Out EQ will be set to the B2 curve with the B2 switch set to Normal.
— Source Craig-at-Bose

No cable plugged into the Bass Line out

B2 Bass Modules connected Output EQ Bass Signal Gain Notes
1 40Hz-200Hz B2 specific EQ as set by the B2 Bass Level Switch ( + Normal - ) is present at the Bass Module Out and the Bass Line Out Reference Level There are three B2 EQ settings possible using the B2 Bass Level Switch ( + Normal - )

Cable connected to the Bass Line Out

B2 Bass Modules connected Output EQ Bass Signal Gain Notes
0 40Hz-200Hz B2 EQ as though B2 attached and B2 Bass Level Switch set to Normal position Reference Level This presents the B2 EQ with the B2 Bass Level Switch set to the Normal position. (No resistance detected between the 2+ and 2- pins of an NL4 plug)
1 40Hz-200Hz B2 specific EQ as set by the B2 Bass Level Switch ( + Normal - )
is present at the Bass Module Out and the Bass Line Out
Reference Level If you are using a PackLite® power amplifier model A1 Extended Bass Package this is a total of two B2s (one on the A1 and one on the Power Stand)

Powered Subwoofers

The Model II is an integrated system that supports Bose B1 and B2 bass modules. Connecting powered subwoofers to the Model II Power Stand Bass Line Out is not supported because EQ curves for the B1 or B2 are present at the Bass Line Out. This may or may not result in good results with a powered subwoofer.

If you want to use a powered subwoofer, connect your signal source to the subwoofer and connect the subwoofer high pass filter output to the L1® (any model).

Output if no B1 Bass Modules detected at the Bass Module Output (powered output) the signal at the Bass Line Out is:

  • 40-200 Hz with B2 EQ applied if you have the current L1® Model II Power Stand Firmware Updates
    • If you do not have the current firmware the signal at the Bass Line Out is: 40-200 Hz Bandpass (that is: NO B1 EQ) [1]
  • The system Crossover for the Cylindrical Radiator®s is 200 Hz

If one or two B1 Bass Modules is detected or emulated using resistors across NL4 2+ / 2- pins

  • 40-200 Hz with different EQ curves
  • The system Crossover for the Cylindrical Radiator®s is 200 Hz

For details on how to do this see: Activating B1 EQ Curves and Using a Different Sub


Note — Operation of the B2 with the Model I/Classic is only supported with the B2 Bass Level Switch set to Normal.
See: Is the B2 Bass Module Compatible with the L1® Classic or Model I


Bass Module Output (powered output)

For the sake of those attaching third party passive speakers (an unsupported application), the output characteristics are the same as for the the B2 Bass Module (section immediately above).



  1. Hilmar-at-Bose intelligent crossover
    A) When there are no bass sources attached, lower the crossover and try to get as much bass out of the L1 as is reasonably feasible (110 Hz) in this case
    B) If there are bass sources bring the crossover up to 180 Hz (where the L1 starts to get really efficient) AND adjust the bass gain so that the overall spectral balance is maintained no matter how many bass sources are attached.


Original Source - Hilmar-at-Bose




L1 Model II Crossover

There is no change in crossover frequency for the Cylindrical Radiators® depending on the presence/absence of B1 Bass Modules attached to the Bass Module output. This is due to the design change (Cylindrical Radiator® is not ported whereas Classic and Model I are.) The L1 Model II is designed to always be used with at least one B1, whereas the L1 Model I / L1 Classic was designed to used with or without a B1 Bass Module.

B1 Cable Warning

Warning - Use Blue B1 Cables NL4 cables with your L1 Classic / L1 Model I / L1 Model 1S L1 Model II

Classic This information is applicable to the L1® Classic
L1 Model I This information is applicable to the L1 Model I
L1 Model II This information is applicable to the L1®  Model II
B1 Bass ModuleThis information is applicable to the B1 Bass Module
B2 Bass ModuleThis information is applicable to the B2 Bass Module

If you are using a B1 Bass Module with your Power Stand it is ESSENTIAL for proper operation that you use the BLUE cable supplied with the B1 Bass Module or B2 Bass Module. This is required so that the L1 Classic/L1 Model I/L1 Model 1S/L1 Model II Power Stand can correctly identify when there are bass modules connected to it and if so, how many.

B1 Cable


Please click the picture above for ordering information.

Note
The B2 Bass Level Switch will not change the sound of the B2 Bass Module if you are not using the correct cable.

See: PS1 Power Stand / Bass Line Out for details about how the Power Stand adapts to the number of bass modules are connected to it.


You may also use high quality NL4 cables (four conductor cables). Alternate and longer cables for B1s